WJSR2070D0WW General Electric Washer - Instructions

Removed the knob from water level switch. Removed 4 screws holding the control panel cover on and leaned it out. Made sure the washer was unplugged and removed the three wires and removed the water level hose and the switch. Installed the new switch and hose plugged the wires back in and put things back together. Washer works fine now.

Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

Using screwdriver and pliers removed old knob; replacement snapped on easily.

Reading all the other stories helped me get started. One tip I want to share is when removing the old coupler, I held on to a pulley puller by hand. I hooked the jaws underneath; while I pulled up on it, I would tap with a hammer on either side of the old coupler. This gave me the leverage needed to make it pop right off.

The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

1, remove agitator. 2 on top of the agitiataor coupling you will see a bolt. Rap lightly with a hammer and with vice grips gently remove the bolt. why vice grips if its been in there for awhile this will be your best choice. No worries the kit comes with a new one.3 Pull the coupling sraight up and out. 4. Align the splines of the new coupling with shaft and gently tap the new one on. 5 Lube the oring and tighten bolt. 6 align the splines of the agitator and gently seat the agiator all the way down. might take awhile to align everything.
trouble shooting tip remove the front cover, turn machine on and hold the agitator, no, not the kid, the one in the machine. If the agitator stops moving but the machine continues to work and the belt or pump shaft turns its the coupling.

This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,

I also spent less than 12.00 to fix and a new one is over 600.00.

Thank You
Christine brooks

Removed old knob. Inspected timer and dial. At first it looked like I would need 3 parts Knob, dial and timer. Timer and dial were back orderd and knob was shipped. After I recieved the knob I tried it and the problem was solved. Part select canceled the rest of the order and credited it back to my charge card. Great customer service!