WKSE6280B3WW General Electric Washer - Instructions

Was easy. Removed pump, ordered yours and replaced

After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.

Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.

If you follow the video that part select provides you will be just fine.

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.

Removed the old pump put in the new one

removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..

I googled "water not draining washer" and found a video made by Partselect.com on youtube on how to replace the water pump for a washer. So, I went to their website and punched in the model number of the washer and found the water pump I needed in stock. It said it takes an average of 1.8 days for delivery. I ordered it on a Sunday and by Tuesday I had the part delivered to my front door. That night after work, I went down to the washer which I already had sitting face down on the floor with the back peeled off and the pump out from the weekend so I could compare how it looked with the online pictures. The new part came already mounted on a new bracket so it was just a matter of installing the bracket and hooking up the intake and output hoses. In order to make my job easier in the tight space, I removed the drain hose from the bottom of the wash basin by squeezing the pressure clamp with a large pair of adjustable pliers. I then installed the other end of the drain hose to the pump itself. I then hooked out the end of the output hose to the other part of the pump that pumps out the water to the sink. I first removed the clamp on the back of the washer that held the output hose to the back of the washer. That gave me more leverage to move the pump around for the installation. Once both hoses were clamped onto the pump, I used a ratchet socket wrench to install the two bracket bolts directly onto the base of the inside of the washer in the same holes using the same bolts as the old pump. Once that was tightly installed, I Hooked the other ends of the two hoses to the bottom of the wash basin and to the back of the washer respectively. FInally, I connected the ends of the two wires into the clips on the pump in the same order as the original pump. One white one black. Finally I screwed in all the short sheet metal screws that held the back washing machine cover on. It was about 12 screws. I then installed the drain hose with the original bracket to the back of the washer. Satisfied that everything was installed tightly, I stood the washer up and then hooked the water hoses back up to the faucets and tightened them snugly with the large adjustable wrench to ensure it did not leak. I plugged the washer back in, hooked the drain hose to the sink and then filled the basin up partially. Moved the control to the drain mode, and the water came out wonderfully. Note, when the pump was broken, I was able to drain most of the water from the wash basin by lowering the drain hose the a bucket on the floor and letting gravity do the work of draining it. I had to fill the bucket several times and dump it into the sink, before I was able to drain all the water out and then lay the washer face down on the floor to remove the back of the washer. Thanks for the part and quick delivery. I saved a lot of money on repairs by doing it myself.

Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.

watched Partselect video and followed instructions step by step

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.