WPSQ3120TAAA General Electric Washer - Instructions

It was really simple just pull up the agitator and take off the screw that holds the coupling down slide it off and put the new coupling on and you are done.

removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.

I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone

Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.

First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).

The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len

First, I removed the agitator by reaching in the washing machine and pulling up on the agitator until it popped off. Next, I removed the 1/4" bolt that attached the coupling to the spline. Then I removed the coupling. After removing it, I replaced it with a new one, installed a new bolt, and reattached the agitator. It took 2 days for me to get the part(ordered on a Sun)but only took me 10 minutes to repair.

I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

removed agitator unscrewed agitator coupling replaced with new one replaced agitator

I had no intention of trying to fix the washer myself after reading about how to do it, only because I didn't know what half of the words were referring to. But once I watched the video, and I saw that the part was going to cost less than $15.00 (shipping included), I thought I would at least try it before going out and buying a new machine. The washer in the video was slightly different than mine, but I recognized the parts from my machine and mine was actually easier to replace than the one in the video. I just pulled off the agitator, unbolted the old agitator coupling and replace it with the new one, bolted it back on and lined up the agitator grooves with coupling and that was it. It worked and saved me a lot of money. I once had an appliance repairman tell me that if your washer or dryer lasts 7 years nowadays, you should consider yourself lucky. Mine is 7 years old, so I thought I would have to replace it. I didn't particularly want to pay someone $100.00 to come to my house and tell me it couldn't be fixed if I was going to have to buy a new one. But fixing it myself was very easy. Written instructions never would have worked for me, but the video was very helpful. Thanks!

Unplug power. Pull up firmly and quickly from the base of the agitator. Some videos used a rope and 2x4, I didn't have to. The agitator just pops right off. Then with a 7/16" wrench unscrew the bolt while holding on to the coupling. Take agitator coupling off. Clean off metal grooves that the coupling goes on, use either a small screwdriver, metal brush, a knowl, just to make sure you will have good connection with the new coupling. Then install the coupling, new nut, tighten nut firmly. Install agitator pushing down firmly on opposite sides until snaps in place. Turn agitator by hand, it should not free spin. Plug power back in, run washer with water and bleach only in the smallest setting and let it run through its cycle. This will take care of any black debris that might have got into the bowl while fixing. GOOD LUCK!! I also used videos found on Google.

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.