WCSR4110T6WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Walter from Boone, NC
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Start knob was broken
Ordered new knob from you people and simply replaced borken knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rahway, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Murphy, TX
- Parts Used:
- WH2X1197
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
The machnica had recently developed a rumble during the spin cycle
The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy W from Albany, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
On knob was broken
Removed knob and installed the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Spanaway, WA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob on dryer broken
There really is not much to explain, the new knob was so simple to replace that my six year old could have done it. No tools were required and it took less than a minute to replace the new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Dunmore, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer wouldnt start
just replaced the old knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Levittown, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob
the part fixed all the problems in a cinch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wagdy from Watertown, MA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The two dial buttons were broken on a white appliance. The dials sent were bone white.
Pull out old, insert new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Portland, OR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bdryer broken knob
I just put the new knob where the old one was and presto it was done. The whole process was much easier than I expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Tampa,fl, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plasic knobs were broken
An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Cody, WY
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob on my 15 year old dryer
The knob to start my dryer broke about a year age. I was using pliers to start the dryer. I was sure I would never find a replacement part and it was just a matter of time before the plier trick would break the start knob. I decided to look on line for a replacement knob sure that I wouldn't find one. Clicked on PartSelect, enter General Electric dryer and a bit more simple info and there was the part I needed. This site has everything. My dryer is good as new. Thanks PartSelect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from St. Simons Island, GA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer on/off knob broken
The pictures really made it possible to determine exactly which knob was what I needed for my dryer. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Austin, TX
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken "start" knob
The start knob had crack in it that was getting bigger, and we'd begun using pliers to start it. Not only was it unwieldy but I thought it would eventually strip the metal stem. Of course this was a breeze of a repair--we just slid the new knob on. But my husband had been certain that finding a replacement knob--or calling a dealing and ordering the part--would be a big deal. I said: "But let's just try on-line." We quickly found the model # inside the dryer door. We filled in the appliance info, the part popped up. I ordered it. It arrived in 2 days. It's like new.
Was this instruction helpful to you?
Thank you for voting!