WMSR3110W0WW General Electric Washer - Instructions

I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.

Popped the front off the washer by placing a towel under the screwdriver to prevent chipping the paint. Had to spent almost 45 minutes soaking up water that had leaked from pump. Must have been leaking for some time before enough leaked under washer and became visible, because there was a lot of rust build up. (1).Removed old pump by first un-pluging washer and them removing (2) connecting wires from pump. (3).Next use nut driver to loosen flex hose from washer. (not from pump). Loosen spring clamp from discharge hose , and slide up. (4) Using nut driver I removed (2) hex screws that held pump to frame, then removed pump and motor assembly. (5). Mopped up water with large (old) bath towels (6). Used hair dryer to dry area. (7). Used wire brush to brush away surface rust. then used small shop vacuum to remove this surface rust. (8). Used small brush to paint white rust-olem paint on rusted areas, used hair dryer again to help paint to dry, then gave it a second coat and again helped it dry. (9). I then removed flex hose from old pump assembly, checked it for cracks and finding none I attached it to new pump with existing spring clamp. (10). I then put pump assembly back inside washer, but did not attach with hex screws yet. (11). Re-attached the drain hose by sliding the spring clamp back down, making sure it is around the hose and discharge spout. (12). Reattach the flex hose to washer discharge spout. (13). Screw new pump and motor assembly unto newly painted frame. (14). Re-attach (2) wires to pump and motor assembly. (15). Plug washer back in and try filling it with some water, letting it go into the drain cycle to check for leaks. NOTE: You don't have to go through and entire wash cycle. Just use the dial to put some water in then move it to drain and /or spin to get the new pump and motor assembly going. I did this a couple of times and then did an entire load of clothes to ensure there were no leaks. After I was sure there were no leaks, I simply popped the front panel back on. My part cost a total of $64.00 including shipping, and it took me about 1 hour of my time. I checked with my local GE dealer and his cost would have been $98.00 for the part, and $85.00 for labor for a total of $183.00. I AM VERY HAPPY. Oh bye the way I had my part within 3 days of the order and that was with regular shipping. I will always use Parts Select from now on.

I used a pair of needle nose pliers and a screw drive to remove the clip holding the knob on its shaft. The new knob came with its clip already in place, so it "popped" right on. I ordered the compression ring in error and it it was not needed

1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.

Uhhhhhh.... Pulled knob off. Pushed new knob on. Took all of 5 seconds.

I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.

Removed front cover(use screwdriver)clips on top of cover under lid
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.

Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy

I replaced the old knob with a new one.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!