WPSE7003A9WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Rochester Hills, MI
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Wash basin wobbled excessively
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
Super easy and super cheap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Marco Island, FL
- Parts Used:
- WH13X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Solinoid chattering when cold water was used
Removed 4 screwes on the top of the washer. Layed down the control panel and there was the inlets. Removed two screws and loosened the hose clamp. removed and installed new part.
It did the trick. No more problems.
It did the trick. No more problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Butch from WATER VALLEY, MS
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Machine would not agitate.
Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Nokesville, VA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
some leak
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer
sincerely, a satisfied customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from VERMILLION, SD
- Parts Used:
- WH02X10383
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
Leak
You tube is the only way to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Ventura, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump was leaking due to a crack
We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Betterton, MD
- Parts Used:
- WH45X10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The machine would not spin and the agitator seemed to be siezed up. The inner tub had cracked and broken completely loose causing it to jam against itself preventing any movement.
1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from saint Clair Shores, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Agitator had little to no movement
I removed agitator by pulling it up until it unsnaped.
I removed the old agitator coupling by removing the bolt and pulling up while twisting it.
The new coupling looks different than the old part but fits the same.
I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.
Washer runs like new!
I removed the old agitator coupling by removing the bolt and pulling up while twisting it.
The new coupling looks different than the old part but fits the same.
I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.
Washer runs like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Goran from Longview, TX
- Parts Used:
- WH13X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water would overflow the machine and flood
Problem was intermittent. It would happen once a month or so. Eventually I set next to the machine and kept turning it On and OFF through cycles for about a half an hour until it failed and I was able to confirm that problem was with the water valve.
Buying and replacing the water valve was easy.
WARNING: UNPLUG THE WASHING MACHINE FROM THE WALL BEFORE ATEMPTING ANY ELECTRICAL WORK ON YOUR WASHING MACHINE!
Buying and replacing the water valve was easy.
WARNING: UNPLUG THE WASHING MACHINE FROM THE WALL BEFORE ATEMPTING ANY ELECTRICAL WORK ON YOUR WASHING MACHINE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from NIAGARA FALLS, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The unit was moving all over the place
I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Due West, SC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
My Washer stopped agitating
Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from rESACA, GA
- Parts Used:
- WH13X10024
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hot water inlet valve cracked
My son repaired the washer . It was really easy to fix. He had it working in about 15 minutes. Thanks to PartSelect's fast delivery service I was only without my washer 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Holly Springs, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washing machine would fill, spin, and drain, but would not agitate
After doing some troubleshooting, I found that the Air Bell was stripped inside.
First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.
Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!
First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.
Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Clinton, NJ
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Pump was bad
I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Herrin, IL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Pump was making grinding noise
Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!
Was this instruction helpful to you?
Thank you for voting!