WISR106DGCWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patrick from San Antonio, TX
- Parts Used:
- WH01X39337, WH1X2721
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Tub dampening straps needed for repair
Check on internet on how to use a putty knife to remove the front panel (slip it into the crack between the top lid and front panel). Then you can see the straps that are broke, figure out which screws to remove to gently lift the top lid to get at the pieces holding the straps in. Pretty simple, just remember to unplug the machine before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Utica, NY
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Washed my daughter's toys and broke the agitator
Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Chesnee, SC
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Had a small water leak gettin into the drip pan.
Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from West Memphis, AR
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer flooded my laundry room!
Pried the front cover off the washer and then rotated the tub around for easier access to the hose clamp. Used screwdriver on hose clamp then detached spring clamp from pump inlet. Reversed the procedure for repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from St. Cloud, MN
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Leaking hose (had a rip in it)
First I had to remove the front cover to the washer.
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).
Then it was just a matter of using the nut driver to loosen the clamp holding the hose to the tub portion, and a channel lock for the clip on the drain pump. Pull the old hose out, do the same thing vise versa for the install... Only hard part was the clamp on the drain pump was being a little difficult (but no big deal).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Boone, NC
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer Start knob was broken
Ordered new knob from you people and simply replaced borken knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rahway, NJ
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janis from northridge, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Easy. Pulled off old one slipped on new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Miami, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Pulled the old knod off and put the new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annamarie from FORT LORAMIE, OH
- Parts Used:
- WH43X10032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not agitate
Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the problem.Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Kiln, MS
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from TUSCUMBIA, AL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken starter knob
Just pushed the knob on by hand and it was ready to start! It was great not having the extra expense of a house call! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harwinton, CT
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!