GJRR4170H0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tony from DOVER, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Tub shacking
Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from LA QUINTA, CA
- Parts Used:
- WH12X10334, WH01X10302, WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
tub moving allover the place
replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from ROCKLEDGE, FL
- Parts Used:
- WH11X10049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Indicator dial broken
The dial is held on the cycle control shaft w/a clip. Using a small pair of long nose pliers, pull the clip out of the slot in the control knob. Remove the outer knob exposing the indicator.Easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erica from ATLANTA, GA
- Parts Used:
- WE01X20378
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer was not turning on.
I bought all three parts but I noticed that the dial was very loose. I reapaired this first and it was working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from MORGANTOWN, WV
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was cracked and the metal "D"-Ring was broken on my GE cloths dryer
This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from LONGVIEW, TX
- Parts Used:
- WH01X10310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
selector knob plastic teeth mostly gone, difficult to select wash cycle
Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from BROCKTON, MA
- Parts Used:
- WX05X20641, WH01X10302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken drive brlt
I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SAINT CLAIR, MI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining out of the washing machine
The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from WICHITA FALLS, TX
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water dripping into washer when not in use
I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from PEARL RIVER, LA
- Parts Used:
- WH38X10017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Had to make the 1-11/16” spanner nut tool
Followed the video guidance supplied by this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beata from STUART, FL
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Water dripping into the washer when washer was not in use
I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WH02X10383, WH2X1198, WH2X1197
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin, leaking water
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from LAKE ST LOUIS, MO
- Parts Used:
- WH2X1198
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
hammering on the tub nut wrench rotated the drive axle & pulley
I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Traci from TRACY, CA
- Parts Used:
- WH01X10302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Washer won't agitate or spn
Followed the instructions on repair clinic video
Was this instruction helpful to you?
Thank you for voting!