WPSR3100W0AA General Electric Washer - Instructions

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

Removed fabric softener cover by pulling up. Then removed agitator by grabbing at the bottom and pulling up. Note I did read online that some may have a bolt holding the agitator down thats what it seemed like when I read it. Mine did not have a bolt. after removing the agitator there is a 10 or an 11mm bolt holding it down remove that and the coupler comes right out then install in reverse order. All done. Also its a ge adora washer.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !

First I had no idea what to do. My first thought was to buy a new washing machine and so I began searching and found that a washer equal to mine was over $600. I brewed on this for a few days when a neighbor told me that they are not that hard to work on and we should take it apart and look at it first. We took the top and the front of the washer off and looked at the belt and the motor. All seemed fine. (we just used a screwdriver for that) then we took the agitator off, it pulled right off with some heavy tugging. then we saw the coupling. It was only held on by one screw. We used a socket to take the screw out and pulled the coupling off. It is supposed to fit very tightly on a shaft with gears. When we pulled it off and looked inside it, all the plastic gears in the coupling were stripped and that is why the agitator would not move. I expected this to cost me at least $50, but to my surprise the part was only $6.50. The shipping cost more than the part. When it arrived in about 3 days. I literally had the part on and the washer back together in less than 5 minutes. The entire repair cost me $14 and now the washing machine works better than it has worked in years. Who knew. If you intimidated by working on washers, don't be, they really are very simple machines and so not worth calling a repair man for.

I used the video instructions sent to my email and everything worked perfectly as instructed.

Found out the screw was stripped from the agitator, probably because the washer is over 10 yrs old. We got the right part! The parts store was very fast in shipping, in fact we got it the next day! Highly recommend PartSelect!!!!!!!!!!

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

The washing machine was a making a very loud noise when it got to the end of agitation and though it did complete the cycyle it was beginning to snag clothes under the agitator....don't know how. Found that the agitator coupler was cracked in 4 places. Washer is only a year and a half. 4 family washing..so I wanted this fixed quick. The part came super quick..like two days and I was not expecting it for 4 - 10 days...so great and it was cheaper than other places I checked even with paying shipping! I watched the video of installing the coupler--very helpful! I removed the agitator, then removed the agitator coupler....this was already done before the part arrived. When the new coupler arrived, I just had to drop it down onto the spline...there are grooves it must fit to...then I applied the hold down bolt. I used my wrachet/socket to tighten it, but you can use an adjustable wrench. I'm short so reaching down into the washer bowl to get to tighten the bolt was a little ackward..should have used a stool. The loud sound the washer was making before replacing the part stopped and I am back in business...doing ugly washing....LOL! One thing I will mention....nothing to do with the part...but I had without thinking placed the agitator back into the washer bowl....WITHOUT bolting it down..then put the agitator on top of the old coupler. So this made it lock in place under the agitator. My agitator does not have an opening at the top after removing the dust cap inside so there was no way to knock the coupler down and out from the top by putting a long wrench or something down through the top of the agitator(the video shows how to do this also)...sooo....because the agitator coupler locks in place behind moveable clips, I took eight butter knives and wedged them behind each clip on the underside of the coupler pushing each back and was then was able to separate the agitator coupler from the agitator by pulling it forward with my fingers...so don't test putting the agitator over the coupler without first bolting it down! This is all a lot to say about such a small part but this small part is crucial to being able to complete a wash..an ugly wash that is...haha!

remove the agitator by just pulling it up, remove the bolt that hold the agitator coupling down and install the new one.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

Easiest repair ever. My wife actually did the repair because I thought I'd need more time to do it. She just pulled the agitator staight up and out then removed the bolt holding the coupling, pulled out the defective coupling and put the new one in, replaced the bolt, slid the agitator back on and it worked perfectly! Thanks for making a $60 or more repair call a $13 dollar self repair. And that includes shipping! We will always use your site for future fixes.

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.

removed agitator unscrewed agitator coupling replaced with new one replaced agitator

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.