WBSR3140D2WW General Electric Washer - Instructions

I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.

1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...

Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.

The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It required a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.

The teeth on the control knob were broken off (not sure how it happened). the teeth on the stem of the knob turn the selector dial. To replace the control knob, I used a pair of needle nose pliers to remove the pin clip and pulled the knob off. The new control knob came with the clip already installed on the stem of the knob. It was a matter of pushing the new knob onto the shaft . . . and the rest is history.

Too easy! Push on dial, push on knob, insert clip. Done. Back in the day a repairman would have probably sold me a new timer with that knob and dial!

Had never repaired a washer before, but have several tools and enjoy working with my hands. Knew it would be cost prohibitive to call a repairman, and didn't have anything to lose. Quick delivery from partselect -- reasonable price, too. This was as easy as simply taking the whole washer apart (NOTE -- there are instructions behind the knobs inside the unit that are very helpful!) replacing the transmission and putting it all back together. Hardest part was getting the hub nut off of the transmission axle. To get it off (REVERSE THREADED, so 'tighten' to 'loosen') I used a 1 11/16 socket and impact wrench. Use the same tool to tighten (but go EASY...don't overtighten). This was not difficult, but just took some time. A couple of evenings later, we were washing again like NEW. Part cost around $160, labor was 'free' and much less than a new $500 top loader or $800 front loader. If you enjoy taking things apart and have some tools, then go for it!

First I removed the front panel by prying it forward with a Screw driver away from the side panels at the top (wrap a shop rag around the Screw driver to keep from scratching the paint). Once you have the panel pried loose at the top ... lean it forward until you can lift it off the tab type hooks at the bottom.
I next unplugged the wires from the motor. The orginal motor had three wires ... two on top and one on the left side. The one on the side is a ground wire for the open frame motor. The replacement motor is sealed and does not require this wire. Just leave it unplugged when the new one is installed.
Next I removed the inlet hose that attaches to the back of the pump. Remove it by loosening the hose clamp and removing it from the bottom of the tub, leaving it attached to the back of the pump. It is much easier to remove and transfer to the new pump once it is out rather than fight with the spring type clamp on the back of the pump in the close quarters inside the machine.
Next I removed the outlet hose from the top of the pump. Squeeze the spring clamp with Pliers and work it up and off the pump.
Now I just used a Socket to remove the two bolts holding the bracket to the inside front of the machine and removed the assembly.
I now removed the inlet hose from the back of the old pump. Just squeeze the spring clamp with Pliers and work it up the hose and off the pump. Transfer the hose to the back of the new pump reusing the same clamp.
I now bolted the assembly back into the machine, reattached the outlet hose to the pump, and then reattached inlet hose to the bottom of the tub. All that was left to do was plug in the two wires to the top front of the pump motor (as I mentioned earlier, leave the side wire from the old pump unplugged as it is not needed on the new one). I then ran the machine for a few moments with the front off to check for any leaks and then put the front panel back on.
The whole replacement cost about $50 and took barely 15 min. from start to finish. The machine now works perfectly.

1. Noticed there was and obstruction in the air line that feeds the water level pressure switch. Cleaned out the air line but still had intermittent problem with flooding.
2. Evaluated the fill solenoid valve with meter and was functioning properly
2. Evaluated pressure level switch with meter and noticed that the switch was not changing state as it should when the water level is increasing. Replaced the level pressure switch, but still had problem.
4. Noticed the air line was damaged and had a hole that prevented pressure from building up. Replaced the air line and all is good!

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and the tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

Actually putting on a knob is self-explanatory. But wanted to say your company had the best price and reaction (delivery time). Great job by PartSelect!

Instead of calling a repair man, we decided to look up the problem on the internet. We found that other people had the same problem on a website such as this. We narrowed it down to 2 parts. I opened up the panel on the washer where all the controls are (only 4 screws). Inside the panel was a diagram of the washer. We thought it would most likey be the Water level Pressure Switch. I found the part right away and removed it, I removed two connectors. It was really easy.
We ordered the part online and it came really quick (within two days). I installed the new part(Water level pressure switch) and tested it. The washer worked perfect and did not overflow. We tested it again with a load of laundry. Everything was good.
We saved a lot of time and money by fixing it ourselves. We did not have to wait around all day for a repair man and the part was under $30.00. I am happy the way it all turned out.

First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.