WLCD2050D1WC General Electric Washer - Instructions

removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.

Removed the old pump put in the new one

removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.

The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.

follow youtube vid. simple

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

My washing machine would not agitate. I looked online for the possible repair solutions under GE website. All I needed was my model number. I typed in the model number and it gave me possible solutions. I ordered the parts from part select. Once they came in, I then went online to find video of how to repair the machine. When I found the video I needed I began disassembling my machine. I pulled the agitator off with a brisk tug and used my socket wrench to unscrew the coupler nut. Once that was off, I installed the new coupler tightened the bolt and installed the agitator. I filled the machine enough for a small load and sure enough, it worked! I did not need to use the belt, but I will have it on hand if I need to. I saved on separate shipping. VERY PLEASED!

Simply unclamped the lower end of the hose, then used the nut driver to release the upper clamp of the hose. Took it off, replaced it with the new hose and re-clamped both ends. It took me about 12 minutes to do this. Very easy repair!!

watched Partselect video and followed instructions step by step

Took the front cover off and tapped the motor on the old pump with the end of a screwdriver. The pump immediately started pumping,so, I knew it was the problem. Ordered the new pump and motor from PartSelect and received it in 2 days. Removed the old assembly and replaced it with the new one in less than 30 minutes per the video instructions on PartSelect's website. Wife is happy :) and I saved at least $100 bucks, probably more. Btw, a local appliance dealer where I bought the washer, wanted $63 for the pump/motor assembly and said it would take 4-5 days to get it. I paid $42 including shipping from PartSelect, and received it in 2 days!

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.