WBB4500K0WW General Electric Washer - Instructions

just like the video showed/////only idid not kno the water would escape from one of the hoses when removed///video did not prepare me for this

took off the front and replaced easily. I tested it and it worked! The trick to remove front panel is use 2 screwdrivers, one on side, one in front even to lid edge.

Replace

"Thought" the belt was the problem - ordered new belt - waited for belt to arrive - opened washer. Belt was in perfect condition - problem is the clutch. Next time husband will verify problem before ordering parts.

I figured out the problem,watched the video instructor and i did it,couln'd be easier guy h

I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!

the repair was easy. I will be call you again, thank you.

ordered new one put on works like a new machine your repair website really helped.

Replaced the button and was working in less than Fifteen Minutes.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

I searched the internet for the problem resolution & purchased $40 of the parts before I disassembled the machine. This was to minimize the downtime. Not one of the internet sites recommended changing the shaft & mode shifter assy so all the parts I ordered were not needed. Once I determined the correct part I had the reorder & pay expediting fees to deliver next day.

After watching the YouTube video on how to disassemble the GE Profile washing machine the repair was relatively simple.

Inside the appliance is an instruction sheet that describes replacing the part and followed it mostly. To improve your instructions, pictures with the instructions are much more effective and easier to understand.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

I laid the washer on its front and removed enough screws to fold the bottom out enough to reach it. I used a wire tie to secure the belt to main pulley and slipped it on the drive. This would have been nearly impossible without the install tool as it stopped the belt from slipping off of the drive. It was simple to turn the pulley clockwise to walk the belt onto it. The whole repair took about 1/2 hour, would have been less if I had used the wire tie at the very beginning.