GTW845CPN1DG General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from Cypress, TX
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench (Adjustable)
Washer would not drain after a load of wash
Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from FOLEY, MN
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Wash machine would not drain/pump water out of machine.
1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindy from LILLINGTON, NC
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Columbus, OH
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer would not empty when it hot drain cycle
Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from MUKWONAGO, WI
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine would not drain
I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Oxford, GA
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer would not drain
Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Kalispell, MT
- Parts Used:
- WH43X31240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The washer agitator/auger broke off of the base during a wash cycle. The small plastic clips broke off the auger so it couldn't be put back on the base.
The agitator/auger was easy to replace - it just snapped into place. We watched a YouTube to make sure to lock it into the counter clockwise direction.
This saved lots of time and the cost of a repair person to come.
This saved lots of time and the cost of a repair person to come.
Was this instruction helpful to you?
Thank you for voting!