VLSR1090GW General Electric Washer - Instructions

watched Partselect video and followed instructions step by step

I googled "water not draining washer" and found a video made by Partselect.com on youtube on how to replace the water pump for a washer. So, I went to their website and punched in the model number of the washer and found the water pump I needed in stock. It said it takes an average of 1.8 days for delivery. I ordered it on a Sunday and by Tuesday I had the part delivered to my front door. That night after work, I went down to the washer which I already had sitting face down on the floor with the back peeled off and the pump out from the weekend so I could compare how it looked with the online pictures. The new part came already mounted on a new bracket so it was just a matter of installing the bracket and hooking up the intake and output hoses. In order to make my job easier in the tight space, I removed the drain hose from the bottom of the wash basin by squeezing the pressure clamp with a large pair of adjustable pliers. I then installed the other end of the drain hose to the pump itself. I then hooked out the end of the output hose to the other part of the pump that pumps out the water to the sink. I first removed the clamp on the back of the washer that held the output hose to the back of the washer. That gave me more leverage to move the pump around for the installation. Once both hoses were clamped onto the pump, I used a ratchet socket wrench to install the two bracket bolts directly onto the base of the inside of the washer in the same holes using the same bolts as the old pump. Once that was tightly installed, I Hooked the other ends of the two hoses to the bottom of the wash basin and to the back of the washer respectively. FInally, I connected the ends of the two wires into the clips on the pump in the same order as the original pump. One white one black. Finally I screwed in all the short sheet metal screws that held the back washing machine cover on. It was about 12 screws. I then installed the drain hose with the original bracket to the back of the washer. Satisfied that everything was installed tightly, I stood the washer up and then hooked the water hoses back up to the faucets and tightened them snugly with the large adjustable wrench to ensure it did not leak. I plugged the washer back in, hooked the drain hose to the sink and then filled the basin up partially. Moved the control to the drain mode, and the water came out wonderfully. Note, when the pump was broken, I was able to drain most of the water from the wash basin by lowering the drain hose the a bucket on the floor and letting gravity do the work of draining it. I had to fill the bucket several times and dump it into the sink, before I was able to drain all the water out and then lay the washer face down on the floor to remove the back of the washer. Thanks for the part and quick delivery. I saved a lot of money on repairs by doing it myself.

This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.

removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks

I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.

Removed the old pump put in the new one

The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

My washing machine would not agitate. I looked online for the possible repair solutions under GE website. All I needed was my model number. I typed in the model number and it gave me possible solutions. I ordered the parts from part select. Once they came in, I then went online to find video of how to repair the machine. When I found the video I needed I began disassembling my machine. I pulled the agitator off with a brisk tug and used my socket wrench to unscrew the coupler nut. Once that was off, I installed the new coupler tightened the bolt and installed the agitator. I filled the machine enough for a small load and sure enough, it worked! I did not need to use the belt, but I will have it on hand if I need to. I saved on separate shipping. VERY PLEASED!