WISQ416CTAWW General Electric Washer - Instructions

Resigning myself to the fact that the washer was broken and I would need to buy a new one, I decided to pull it apart to see if I could see what the problem was (why not if your getting a new one anyway) Once I muscled the agitator off and undid the screw I discovered that the agitator coupler sat on a metal piece that had grooves. Alas...the coupler was worn...there were no grooves left inside the plastic piece. Wondering if I could even find this part I wondered onto this website, plugged in the part number and there it was with pictures and measurements and cheap! Needless to say I ordered it, why not, if it doesn't work I will buy a washer anyway. The part arrived within days. I unpacked the box, opened the plastic, slid it into place, tightened the new screw, replaced the agitator, plugged it back in, started it up and the washing machine was agitating like new. I wrote this long story because the repair was so easy it's not even funny, and I was just going to buy a new washer...

I pulled off the agitator and realized that the coupler was freespinning, it should not do that. I then removed the bolt on top then removed coupler, it was stripped. Got the part number which is on the coupler itself and ordered a new one. Which by the way a newer style is now the oem replacement. Got the new one installed now it is good as new. All you will need to perform this work is a 11mm socket. Takes 5 minutes.

This was an inexpensive part with high probability of needing it, so I ordered it before beginning to take the washer machine apart based on "noisy" symptom. The fabric softener cup pulled straight up easily with no tool. Then, the agitator pulled straight up easily with no tool. The bolt was easy to get to with socket set and the coupler pulled up using 2 small pieces of wood as levers to pull it up evenly and straight. This didn't solve my noise problem, but was an easy and inexpensive fix to try. FYI...when I continued trying to troubleshoot, I took the belt off and the noise stopped, so I think the transmission is my problem. I tried for 2 days with WD-40, then with C-L-R to get the hub nut to move, and couldn't. I then tried to split the nut using a screwdriver and a hammer and it appears to be split in 2 places, but the nut still won't budge. I listed the washer on craigslist today too frustrated with the hub nut to continue the repair job. The cost of a repairman plus the transmission would have been over half of a new washer machine, and I still would have had a 8+ year-old motor, and I ran across a great deal on a scratch and dent model at Sears, so I am replacing the washer instead of repairing it.

it wasn't as hard as i thought it would be. just remove the
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.

I lifted the agitator stragiht up. removed agitator coupling bolt w/pliers. went on Partselect.com to order replacement coupling, which supplied me with exploded diagrams, entered part number in box at the bottom of the screen and waited 2 days. It then took me less than 5 minitues to complete.

took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)

take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.

The start knob had crack in it that was getting bigger, and we'd begun using pliers to start it. Not only was it unwieldy but I thought it would eventually strip the metal stem. Of course this was a breeze of a repair--we just slid the new knob on. But my husband had been certain that finding a replacement knob--or calling a dealing and ordering the part--would be a big deal. I said: "But let's just try on-line." We quickly found the model # inside the dryer door. We filled in the appliance info, the part popped up. I ordered it. It arrived in 2 days. It's like new.

The pictures really made it possible to determine exactly which knob was what I needed for my dryer. Thanks.

The knob to start my dryer broke about a year age. I was using pliers to start the dryer. I was sure I would never find a replacement part and it was just a matter of time before the plier trick would break the start knob. I decided to look on line for a replacement knob sure that I wouldn't find one. Clicked on PartSelect, enter General Electric dryer and a bit more simple info and there was the part I needed. This site has everything. My dryer is good as new. Thanks PartSelect

Installed new knob. No tools required.

First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).