GTW720BPN1DG General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jose E from Mission, TX
- Parts Used:
- WH03X31397, WH03X31937, WH03X28951, WH01X24434
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Grinding noise LIke Gears that are not setting correctly.Disc
Disconnect power,turn off water,disconnect hose hot and cold. Disconnect drain hose careful water may drain out after you disconnect. Move washer to a place where you have enough room to work.Now lean washer to the floor on its back side Make sure to hold the lid from falling back I secure the lid with tape so it would not open. The washer should on its back side , you should see a gray wheel with a nut.Remove nut and pull the gray wheel off. you feel a magnetic pull, Once removed, you will see 3 screws remove stator now remove all screws holding the speed senors remove Mode shifter hold the Clutch because the spring is under it. Once you start it easy to replace. install new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindy from LILLINGTON, NC
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Columbus, OH
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer would not empty when it hot drain cycle
Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Oxford, GA
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer would not drain
Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from MUKWONAGO, WI
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine would not drain
I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Churchville, PA
- Parts Used:
- WH03X35580
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer wobbled during the final spin. I goggled the problem and determined it was the 4 stabilizer rods.
Ordered the parts, watched the video online and now the washer is good as new.
Thank you for a great video and the quick delivery of the genuine GE parts!
Thank you for a great video and the quick delivery of the genuine GE parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!