WISR106CT5WW General Electric Washer - Instructions

Removed by pulling out. Removed coupling air bell with socket and replaced. Wery well. Thnak you.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!

We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod

Should be noted that the basket must be rotated on installation to find the best balance point!

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

unplug machine and turn off water at the valve. the pressure switch is located behind the water level control knob. remove the knobs from the panel, then remove the panel on the top back of the machine and remove the wires from the pressure switch. unplug switch. attach wires to new switch and plug into place. replace panel and replace all the knobs.turn on the water valve and plug into outlet.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.