WWLR3100VWW General Electric Washer - Instructions

Removed center hub and agitator with a sharp tug upward ( no tool required) then using a 3/8 drive and 7/16 socket I removed the stripped coupling and replaced with new one. Total repair time was less then 15 min. 10 of then were spent search web page and watching DIY video clip.

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.

Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

This repair is as simple as it gets. Pull up on the agitator to reveal the Agitator Coupling. Remove the old coupling and reinstall the new one. In addition to this, I found the source of a majority of the mold smell inside the washer machine. There was a build up of detergent under the Agitator. A few scraps of a puddy knife, a shop vac, and the odor was gone. The only caution is to be careful pulling up on the agitator because you could potentially hit your self in the face because it will come off fast. Easy, Easy, Easy.

The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.

Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.

I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks