WPSQ3120TAWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Mechanicsburg, PA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke.
Installed new knob. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Warwick, RI
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Once I found your web page things went very smoothly and quickly. It was exactly what I wanted and it even came a day early. Obviously, no problem with the repair just put the knob in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barney from Boca Raton, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Worked Perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from Lyndhurst, NJ
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Agitator broke
Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jorge from Pinehurst, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the agitator is not moving. (agitating).
take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from reidsville, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
no agitation on washer
it wasn't as hard as i thought it would be. just remove the
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corrine from Minot, ND
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
would not agitate
took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Charlotte, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
washer was making a screeching noise
Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from Summer Shade, KY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
would not agitate
Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from eastaboga, AL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator Coupling Stripped Out, Machine Wouldnt Agitate
Placed hands fiemly on agitator, at bottom, gave a snug pull and removed it from machine, thus exposing the agitator coupling. The coupling is held to main shaft by 1 bolt(11 mm, I think). Removed it, pulled off stripped coulping, installed new, installed bolt, lined up splines on agitator and slid on untill it "clicked" back into place. All done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Onel from Blandon, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
washer would not wash
first i removed the spindle and theni removed theplastic coupling
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Plymouth, MA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
not agitating
I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Brandon, FL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer wouldn't agitate, but everything else worked.
This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rachel from calabasas, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
agitator coupling broke
easy to repair. instructions (with pictures) were included with the part. part came super fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ostrander, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator was not working
Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........
Was this instruction helpful to you?
Thank you for voting!