GDWF800VWW General Electric Washer - Instructions

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

I just removed the clip and took off the old knob. I than put the new one on and replaced the clip.

Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

Popped the lid and activated the lid switch. Agitator danced around but the tub not moving. Agitator was un-snapped so no issue getting it out. Forgot to shut the timer down. By the time I came back with container's for wet laundry the pump emptied the water. Found this web site for parts and liked what I saw on the help. The video was a nice overview but can forget about trying to save the hub nut. The trans shaft has 4 flats on it and years of crud gets drawn into the threads sealing it like it was epoxied in with rust. This one is a 13yr old.
Spent most time reading the help stories and gathering up tools. My concern was getting the bad parts out and that hub nut without more damage. Finally found a 1924 vintage 9" monkey wrench I forgot I had and it fit just fine for putting it back together. I put a 1/8" bit in the drill and put a hole in center of nut next to the flats about 1/8" down by 3 of the flats. Wacked the nut in 2 locations with the chisel in the unwind direction with the corner of the chisel in the hole to put a grove on the nut so to keep away from damaging trans shaft. It finally came off in 3 pieces.
After pulling the basket stuck a rag in the drain hole. The basket sounds like it has water in it but its the counter weight attached on top. Brushed up the crud on trans shaft and sponged out the remaining water and other particles.
Next was a pump inspection. If you take the input line off you can see the impeller to remove any stuff that may damage it. Have to un-bolt the pump be careful on the wiring to pump trying to unplug the wires may damage the connectors or even worse the pump. I mostly had crud in the water on the line.
Ordered the needed parts, and cleaned up the tub, reinstalled the pump. After the parts arrived took about a 1/2 hour to put it in service again. Don't forget to wack the hub nut on tight when installing so it wont come off in use.
Many thanks to all in sharing their story it helped me out to see what to expect.

The worst part of the repair was removing the old hub nut. Don't bother messing with the spanner wrench, unless the washing machine has never been used. Split the nut off with a SHARP cold chisel and a heavy hammer. Be very careful not to damage the threads, because not even GE can or will tell you the die size to re-dress the threads if you damage them. Check drain pump motor to remove debris before using washer. Parts were delivered in a quick and efficient manner.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.