WCCB1030TAWC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mark from st james, NY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
washer was not agitating or spinning
The agitator gets pulled up(no tools required).Under the agitator is the coupling which is held on by 1 bolt.I removed the bolt,took off the old coupling(the inside was stripped where the metal gear meets the plastic coupling).tThe new coupling slides right on.Replaced the bolt.Slid the agaitor back on the coupling.WORKS GREAT.5 MINUTE JOB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Grants Pass, OR
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Machine did not agitate.
Removed dual action agitator to reveal the coupling removed a single bolt and removed old part. Carefully alligned threads and slid new coupling on the shaft and tightened bolt. Put the dual action agitator back on then wa-lah problem fixed. Repair man told me 32 dollars for part plus labor. I fixed it for less than 14 dollars thanks to this site...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ostrander, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator was not working
Replaced the agitator coupling in about 5 minutes, there was only one bolt and it went back togeather. THANK YOU Parts Select..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Philadelphia, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
the agitator on my washer was'nt turning
This was an easy fix. I popped off the agitator, un bolted the agitator couplier and replaced it with the new one. The part arrived in 2 days, the job took 2 minuites. No calling or driving around to find the part, no service charge or repair bill. washer working like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONALD from DURANT, OK
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
would not Agitate
Unplugged washing machine pulled Agitator strait up removed screw from center of Agitator coupling . Replaced coupling put Agitator back on plugged in and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Onel from Blandon, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
washer would not wash
first i removed the spindle and theni removed theplastic coupling
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Pearland, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
agitator was loose and not agitating
First I yanked off the agitator. Then I undid the bolt holding the coupler onto the center of the machine. Took the worn down coupler off, replaced it with the new coupler and bolt. Good as new. GE was going to charge me $85 just for a someone to walk through the door. After parts and labor I am sure they would have charged me $200. I did it on my own for $20 (had the part rush shipped so that was twice the price of the part).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Len from Omaha, NE
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tracey from beverly, NJ
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator spun freely(wouldn't engage)
First, I removed the agitator by reaching in the washing machine and pulling up on the agitator until it popped off. Next, I removed the 1/4" bolt that attached the coupling to the spline. Then I removed the coupling. After removing it, I replaced it with a new one, installed a new bolt, and reattached the agitator. It took 2 days for me to get the part(ordered on a Sun)but only took me 10 minutes to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vino from Hickory, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator stoped moving
I first looked it up on the Internet to see what would be the most simplest way of doing ... I found that brut force was the answer . Take the fabric softner cap off the top of the agitator then with both hands pull the whole agitator up with a lot of force. Once this is done you'll be able to see the coupling and a 7/16 bolt ( 1/4-20 ). Holding it to the metal shaft. Take the bolt out put the new nonestripped coupling in and the rest is a walk in the park.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from whitesboro, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
agitator would just free spin
It was really simple just pull up the agitator and take off the screw that holds the coupling down slide it off and put the new coupling on and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from BISMARCK, ND
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Would not agitate with landry in tub.
removed agitator and coupling, found splines stripped. replaced coupling and installed agitator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Plymouth, MA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
not agitating
I was searching the web and came across this site. I ordered my part that was needed, on Thursday and received it on Saturday. I was very pleased with the quick shipment and price of the part as was my wife. I had it back together in 5 minutes . Thanks Paul Stone
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Brandon, FL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer wouldn't agitate, but everything else worked.
This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rachel from calabasas, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
agitator coupling broke
easy to repair. instructions (with pictures) were included with the part. part came super fast.
Was this instruction helpful to you?
Thank you for voting!