WKSR2100TAAA General Electric Washer - Instructions

1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.

I just added the agitator coupling and screwed it in.

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!

After doing some research on the problem I decided that the rubber tub dampers were probably the problem. Replacing them was simple and straight forward after watching the video. A test spin after installation revealed that the problem still existed. This time I watched the bottom of the tub with a flashlight as the spin cycle began and I discovered that the concrete counter-weight was loose on its platform. General Electric had attached a 5 lb concrete block to the tub support with two self tapping sheet metal screws that had stripped out. I screwed the screws back in and added two nuts to the protruding screw bottom and locked them together. Problem solved. The main difficulty in this repair is reaching to the back of the washing while laying on the floor. And sharp edges on everything.

Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

I removed the fabric softener cup and lifted up on the agitaotor till it slid off. I then removed the bolt that held the agitator coupling in place. I then worked the coupling off, wiggling it side to side until it slid off. Then I slid the new coupling on and replaced the bolt. Lined up the agitator and slid it back on. Then replaced the fabric softener cup. Job could not have been any easier.

Agitator came off easily, but the agitator coupling was a little bit hard to remove. I have to yank it hard to be able to remove it. Putting the new part in is a bit hard too. I had to use a hammer to put it in. (with a piece of wood in between). Tried it with a small load and We're back in business. It was a pleasant experience to do business with you guys. Thanks for the quick turnaround.

Popped the agitator off, removed the bolt, pulled coupler straight up. Reversed steps. Done in under 5 mins.

I noticed that the agitator would spin without any resistance and must be stripped. I pulled the agitator straight up and it came right off. I then used an open end wrench to remove the bolt securing the agitator coupler to the metal spline. It came right off and was obviously stripped. Upon receiving the new coupler, slipped it straight on and tightened the coupler. Placed the agitator on the coupler and tested the washer, it worked. Very easy. My wife was ready to buy a new washing machine and I fixed it with a six dollar part.

Easy as it gets. I did this repair while playing Wii with my 8 year old and cooking supper... Still no more than a 10 minute fix.

Place a towel on one side of the washer so you won't scratch it.

Tie a loop of rope around the middle of the agitator between the upper and lower fins. Wrap the other end of the rope around a 2x4 ( I used a level), or anything similar and wind it around until the 2x4 is pulled down level with the top, keeping one end on the towel.

Yank the other end firmly a few times, and the agitator will seperate from the coupling. I had to snatch it pretty hard.

I removed the 7/16" bolt from the coupling, pulled it off the spline and replaced it with the new one.

The agitator slid right back into place with no trouble, and it is good as new.

What seemed like an expensive repair, or even the need for a new appliance was essentially removing one bolt and a replacing a $6 part.

Thanks!

My husband remove the agitator and found that it was worn. I googled the problem and one of the websites that came up was PartSelect. My husband watched the easy to follow video and had me order the Agitator Coupling Kit. It arrived in just two days. It took him 15 minutes to install and I started washing immediately. It cost us $13.22 and saved us $800 to $1200 if a new washing machine would of had to be purchased. The washer is 15 years old and now with this repair will hopefully continue to wash for a few more years! Thank you PartSelect!

I took the plastic agitator out and checked the agitator coupling underneath. I unscrewed the agitator coupling and looked inside. It appeared that the grooves on the agitator coupling which attaches to the stem had become stripped. I ordered the $6.00 agitator coupling and screwed it back onto the stem. The plastic agitator slipped back onto the coupler and it worked perfectly after that.

To get the old agitator off I first used two pieces of laundry line rope to hook under the fins of the agitator on each side. Next I laid a 5 foot long 2 X 4 across the top and tied the ropes on. I filled the washer with 5 or 6 inches of extremely hot water to help loosen everything up and used leverage to pop the old agitator off. After that I used a socket set to remove the bolt from the top of the agitator coupling and took it out. I then put the new coupling in, replaced the bolt and lined up the agitator and slid it back on until it clicked and locked into place. The washer works great.