GTW335ASN1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kirby from IROQUOIS, SD
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The washer would fill with water then stop.
Open up the top of the washer per instructions. Remove the old switch and wiring harness. Install the new wiring harness and switch. The instructions that were provided are very descriptive so the installation went flawlessly. The switch has been redesigned and looks to be more robust than the original. The washer now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindy from LILLINGTON, NC
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from SUMTER, SC
- Parts Used:
- WH01X27538
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
WASER DID NOT ALWAYS SPIN OUT.
Leaned washer back to get to motor. Loosen screws to remove belt cover. Slipped old belt off, cleaned both spinals off, slipped new belt on. Have a good day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DANBURY, CT
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Water wouldn't drain
Took the belt cover and then replaced the pump. Did a dry run and everything was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from POMONA, CA
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Lid wouldn’t lock keeping machine from working
Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from McKees Rocks, PA
- Parts Used:
- WH01X27538
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Washer not spinning enough to get excess water out of clothes
1.)disconnected washer from water & electric (remember to turn water off 1st)
2.)pull washer out and leaned it back against the wall to access bottom of the washer
3.)remove protective cage covering belt assembly with nut driver. (4 screws and one has a ground wire)
4.)remove old belt by turning pulley’s and nudging it off of the flat pulley.
5.)install new belt groove side in. Put belt on grooved pulley 1st and slowly turn pulley’s while nudging it onto flat pulley.
6.)reinstall protective cage (don’t forget ground wire) and set washer right side up.
7.)slide washer back in place, hook up your water then plug in machine. (Remember to turn the water on)
2.)pull washer out and leaned it back against the wall to access bottom of the washer
3.)remove protective cage covering belt assembly with nut driver. (4 screws and one has a ground wire)
4.)remove old belt by turning pulley’s and nudging it off of the flat pulley.
5.)install new belt groove side in. Put belt on grooved pulley 1st and slowly turn pulley’s while nudging it onto flat pulley.
6.)reinstall protective cage (don’t forget ground wire) and set washer right side up.
7.)slide washer back in place, hook up your water then plug in machine. (Remember to turn the water on)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SAINT CLOUD, FL
- Parts Used:
- WH13X26534
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Some how the renters broke where the water lines connect to the washer
Unplug machine
Move machine out from wall
Removed 4 screws on back plate
Removed the 2 screws holding the assembly to washer
Pulled old unit out and reversed process to put back together
But when I went to test it would not drain tipped washer up and removed hose from motor and found a sock inside
Remove sock and washer runs great.
Just a note this website was very helpful in finding the right part with the exploded view of parts
Thank you
Move machine out from wall
Removed 4 screws on back plate
Removed the 2 screws holding the assembly to washer
Pulled old unit out and reversed process to put back together
But when I went to test it would not drain tipped washer up and removed hose from motor and found a sock inside
Remove sock and washer runs great.
Just a note this website was very helpful in finding the right part with the exploded view of parts
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LEECHBURG, PA
- Parts Used:
- WH13X26534
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No water coming into machine .
Disconnect water lines.
Remove top control panel.
Remove 2 screws & disconnect wires & replace old for new
Remove top control panel.
Remove 2 screws & disconnect wires & replace old for new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from MILLINGTON, TN
- Parts Used:
- WH03X30517
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
washed well but would not shift out of spin cycle
easiest repair I have ever made. No problems and was surprised as to how fast and easy it was to repair. I did not need two of steps the instructions stated I had to do. best purchase I have ever made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adelmo from El Prado, NM
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
the machine was spinning after a load was done,
any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MANCHESTER, PA
- Parts Used:
- WH13X26534
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water dripping after washing was done
Watch a YouTube video on how to fix it. Video was really easy to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from GAINESVILLE, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The machine would not start all the time.
Watched You Tube and had at it. In the end it was fairly simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from MUKWONAGO, WI
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine would not drain
I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from RALEIGH, NC
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The washing machine appeared stuck in the spin cycle
I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Columbus, OH
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Washer would not empty when it hot drain cycle
Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!
Was this instruction helpful to you?
Thank you for voting!