This replacement lid lock keeps your washing machine door securely closed during the wash cycle. If the washer won’t run or the lid won’t stay locked, this part may need replacing. Installation is sim...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This agitator assembly is designed for use in top-load washing machines, where it plays a crucial role in the cleaning process by rotating back and forth to help lift and move clothing through water a...
If your washer isn’t spinning or agitating like it should, this shift actuator might be the fix you need. It helps your machine switch between wash and spin cycles, and is usually found underneath the...
If your washer isn’t filling up like it should, this water inlet valve might be the fix. It controls how warm and cold water enter the machine during a cycle. When it stops working, your washer might ...
This right-side suspension rod and spring assembly helps stabilize the wash tub and reduce vibration during operation. It’s a genuine replacement for select GE washing machines and is designed for dur...
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Emerson
January 7, 2023
Washer starts to fill and stops, open the lid it starts to fill and stops again.
For model number HTW240ASK4WS
Hi Emerson,
Thank you for your question. If your washer will not fill with water, there are some parts that you will need to check to see which one is causing the issue. You will need to check the water inlet valve, the lid switch, and the electronic control board. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
Washer will fill with water and then does not spin. It just sits there full. If I set the machine to drain and spin it will drain but does not go through the spinning part of the cycle.
For model number HTW240ASK4WS
Hello Bernard, thank you for your question. This issue is most likely due to a broken belt. The belt FIX12299369 is necessary for any spinning. We hope this helps.
I have a hotpoint top loader that fills with water seems to be going through the correct cycles but the washer does not spin or agitate. The belt is in tact and I have replaced the pump , capacitor and speed sensor. I feel like this all originated from and unbalanced load of laundry I did when I started the load things seemed fine and when I went back to it later that night the washer was filled with water still with clothes in it. It does get to a point where is just stops in the middle of a cycle and does nothing and stays on a cycle
For model number HTW240ASK4WS
Hi Bernard, Thank you for writing. This could be a faulty Mode Shifter. This he Mode Shifter is responsible for transitioning between agitating and spinning. We hope this helps!
Was this helpful?
Thank you for voting!
Nayan
September 18, 2023
Water is filled under the drum ?
For model number HTW240ASK4WS
Hello Nayan, Thank you for your inquiry. Researching your model, we would recommend checking the drain hoses and seal for any obstructions. If there are none, then it could be an issue with the drain pump. Good luck with your repair.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
