GTW680BPL1DG General Electric Washer - Instructions

Extremely easy. You will need a helper to make it easy. The best directions are on you tube.

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!

Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.

Open up the top of the washer per instructions. Remove the old switch and wiring harness. Install the new wiring harness and switch. The instructions that were provided are very descriptive so the installation went flawlessly. The switch has been redesigned and looks to be more robust than the original. The washer now works like new.

Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!

Replaced water pump. Washer now works as new.
Wife is now happy!

Took the belt cover and then replaced the pump. Did a dry run and everything was fine.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle in half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.

Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great

went online to replace water pump on washer site and followed directions. Very easy installment.

Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!

any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly

Tilt machine back to access pump on bottom of tub. Lay towel down to catch small amount of water. Use pair of pliers to remove clamp from recirculation pump hose. Remove 3 ten millimeter bolts from pump. Then use reverse procedure to install new pump.

There are two lid clips on the front side of the top and a narrow blade putty knife works great to release the clips. There are 4, 1/4 in hex head screws in the back area of the top, two on each side. Two are in the console and two are under the console.
Pay attention to the orange pressure switch hose, when lifting the Console, can pull this hose off, this hose can be pulled off easily. The lid/lock switch is easy to remove, once the Bezel is removed, then slide the switch to the left it will release. Remove and unplug the harness. The new lid/lock switch clips back in the same manner it was removed. Important! When the new switch arrives it may not look like the old one.