This replacement lid lock keeps your washing machine door securely closed during the wash cycle. If the washer won’t run or the lid won’t stay locked, this part may need replacing. Installation is sim...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This agitator assembly is designed for use in top-load washing machines, where it plays a crucial role in the cleaning process by rotating back and forth to help lift and move clothing through water a...
If your washer isn’t spinning or agitating like it should, this shift actuator might be the fix you need. It helps your machine switch between wash and spin cycles, and is usually found underneath the...
If your washer isn’t filling up like it should, this water inlet valve might be the fix. It controls how warm and cold water enter the machine during a cycle. When it stops working, your washer might ...
This right-side suspension rod and spring assembly helps stabilize the wash tub and reduce vibration during operation. It’s a genuine replacement for select GE washing machines and is designed for dur...
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Beyty
February 11, 2022
My washer is flashing pause and lid locked and won't do anything
For model number GTW220ACK5WW
Hello Beyty, Thank you for the question. We suggest pressing and holding Start/Pause button for 5 seconds to see if this unlocks the lid. It can take a few mins to unlock after you press the button. You can also try to unplug the appliance for 5 mins to reset. We hope this helps!
Was this helpful?
Thank you for voting!
Katrina
March 29, 2022
My washer will not spin. The lid lock works fine, it agitates, it fills with water, but I cannot get it to spin. I've been through all the test to get everything to work. But why isn't it spinning?
For model number GTW220ACK5WW
Hello Katrina, Thank you for the question. This could be an indicator that the Mode Shifter is faulty and may need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Why does this washer lose power? Have to unplug it to get it back on
For model number GTW220ACK5WW
Hi Kevin, thank you for getting in touch. Check the washer's power cord for any damage, and lid switch assembly using a multimeter. If they are fine, we would recommend replacing the main control board, part number FIX16874148. We hope this is helpful!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
