GTW755CPM0DG General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from MUKWONAGO, WI
- Parts Used:
- WH23X28418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine would not drain
I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adelmo from El Prado, NM
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
the machine was spinning after a load was done,
any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from RALEIGH, NC
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The washing machine appeared stuck in the spin cycle
I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry W. from TAMPA, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer would not advance to Wash
Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.
Thank you for the super fast service on Christmas eve no less!
Thank you for the super fast service on Christmas eve no less!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from LARGO, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid was forced open and broke latch
Follow the super simple, precise instructions and it is very easy. Only harder part was unclipping the front of the lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scotty from OCEAN SPRINGS, MS
- Parts Used:
- WH08X37938
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The machine stopped working completely! My wife went on YouTube,and learned that it could be the motherboard or the door latch. We changed both, and the washer would only fill but did not drain, and spin! We called a serviceman, and he had to program the service board,but said that the new door mech
We changed the circuit board once, and the door latch mechanism twice because we ordered a faulty part. Then we had to hire a service man to program the circuit board, and to inform us that the door latch mechanism was faulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heath from BOILING SPGS, SC
- Parts Used:
- WH01X24180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Noisy
Took bottom cover off think three bolts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Kalispell, MT
- Parts Used:
- WH43X31240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The washer agitator/auger broke off of the base during a wash cycle. The small plastic clips broke off the auger so it couldn't be put back on the base.
The agitator/auger was easy to replace - it just snapped into place. We watched a YouTube to make sure to lock it into the counter clockwise direction.
This saved lots of time and the cost of a repair person to come.
This saved lots of time and the cost of a repair person to come.
Was this instruction helpful to you?
Thank you for voting!