WVSR1060GW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Garnet Valley, PA
- Parts Used:
- WH11X10049, WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Control Knob Would Not Select Function Desired
Removed retaining clip for knob and removed knob. Installed new knob and clip. Thats it, everything works as reqired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from Granite Bay, CA
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Knob didn't turn easily, pressure needed
Using screwdriver and pliers removed old knob; replacement snapped on easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Fresno, CA
- Parts Used:
- WH11X10049, WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer would not turn
used pliers to pull off clip then poped on new knob very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Knoxville, TN
- Parts Used:
- WH01X10310
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic knob had worn and would not turn dial
Removed old knob. Inspected timer and dial. At first it looked like I would need 3 parts Knob, dial and timer. Timer and dial were back orderd and knob was shipped. After I recieved the knob I tried it and the problem was solved. Part select canceled the rest of the order and credited it back to my charge card. Great customer service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Cheshire, CT
- Parts Used:
- WH11X10049, WH01X10310
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic teeth on the old knob wore out, poor design.
Removed the old knob and installed the new one. Probably will need replacement again in another 3 years..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Medina, NY
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
stripped timer knob
very easy about 1 minute to repair along with how to vidio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from COCOA, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
the water, not get out (drain)
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VITTORIO from PITTSBURGH, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Wasn't Draining
This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from SPARTA, IL
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken control knob
Pulled off the broken control knob (which was really easy, since it was already broken.) Aligned the new knob to the knob shaft which is shaped like a "D", pushed it onto shaft until it was fully seated. Very easy install!!GT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Berecia from WEST PALM BCH, FL
- Parts Used:
- WH01X10310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken Knob and Clip for Washer
I took of the old clip an broken piece of the knob, and removed the selection plate, and push on the new knob and clip, using my pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from LELAND, NC
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The dryer would not turn on.
We took the knob off of the machine and it appeared to be cracked on the inside. We ordered a new one and received it in 2 days. We matched the inside of the new knob to the stem coming out of the machine and placed the knob on the stem. The machine was fixed and we were happy! Thanks Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LACYGNE, KS
- Parts Used:
- WE01X20378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
knobs cracked
Push on. But one pushed in panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hollywood, FL
- Parts Used:
- WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!