WNSR3090V1AA General Electric Washer - Instructions

I noticed that the agitator would spin without any resistance and must be stripped. I pulled the agitator straight up and it came right off. I then used an open end wrench to remove the bolt securing the agitator coupler to the metal spline. It came right off and was obviously stripped. Upon receiving the new coupler, slipped it straight on and tightened the coupler. Placed the agitator on the coupler and tested the washer, it worked. Very easy. My wife was ready to buy a new washing machine and I fixed it with a six dollar part.

Easy as it gets. I did this repair while playing Wii with my 8 year old and cooking supper... Still no more than a 10 minute fix.

Place a towel on one side of the washer so you won't scratch it.

Tie a loop of rope around the middle of the agitator between the upper and lower fins. Wrap the other end of the rope around a 2x4 ( I used a level), or anything similar and wind it around until the 2x4 is pulled down level with the top, keeping one end on the towel.

Yank the other end firmly a few times, and the agitator will seperate from the coupling. I had to snatch it pretty hard.

I removed the 7/16" bolt from the coupling, pulled it off the spline and replaced it with the new one.

The agitator slid right back into place with no trouble, and it is good as new.

What seemed like an expensive repair, or even the need for a new appliance was essentially removing one bolt and a replacing a $6 part.

Thanks!

Popped the agitator off, removed the bolt, pulled coupler straight up. Reversed steps. Done in under 5 mins.

First I uplugged the machine and removed the front cover of the machine by prying outward at the top corners with a screwdriver. Then I removed the two bolts from the mounting bracket and unplugged the electrical wires. Then using a pliers I squeazed the hosed clamps and slid them back on the hoses and pulled the hoses off the pump.

To install the new pump, simply reverse the order and check for leaks. The whole process took about 20 minutes.

I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!

took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!

It was as simple as removing the front cover of the washer. After unpluging, using pliers, remove the two hoses on the pump and disconect the two power plug ins. Two bolts that mounted the pump to the frame of the washer were removed and the pump comes out. Re-install the same way with the new pump from partselect and it worked great.

it wasn't as hard as i thought it would be. just remove the
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.

My washer was full of water after it wouldn't drain as part of the wash cycle. I used a Wet/Dry vacuum to remove the water from the tub. Followed the video provided on this part page. When I pulled the hose from the wash tub to the pump at least a gallon of water that I was in the bottom of the tub and hose rushed into the base of the washer. It was an unexpected mess to clean up a the end of the job. Pump was fairly easy to remove from the washer, but reinstalling the hoses to the pump was slightly more challenging. The hose from the tub to the pump is about an inch too short to make this an easy fit. I had to have my wife hold the hose clamp open with the channel locks while I positioned pump onto the hose. After the hose was installed, the second hose was much easier to install. With the new pump the washer running like a champ!

Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)

take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.

the repair was easy. I will be call you again, thank you.

ordered new one put on works like a new machine your repair website really helped.

First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling

This was a very simple repair. I Pulled straight up on the agitator until it popped off. Then unscrewed the bolt that holds the coupling in place. Due to some corrosion and crud, it took a little effort to get the coupling off. Then I spent a couple minutes cleaning the tub and shaft. The new coupling slid on easily. I attached it with the new bolt, then put the agitator back on and pressed down until it snapped into place.