YWSR2100V0WW General Electric Washer - Instructions

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

This story first. I went to local hardware where I purchased the dryer over 10 years ago and asked them if they could get me a new knob. I had the model number and serial number. They said sure can, but they are expensive. They told me that the knob was around $20. and that the shipping would be $10-$15. . Both was under $14.00 at this site. Just alined the knob up on the stem and pushed it on. THANKS!!

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.

The wife told me that the wash just wasn’t coming out very clean. So I went to check it out and found that the agitator was just moving freely. Upon closer inspection I found that the coupler had stripped.
I was unable to get the agitator free from the coupler so I had to drill out the inside top of the agitator in order to get at the bold that held the coupler in place. Once I got that out the rest was real simple.
Just bolt in the new coupler and snap in the new agitator into place. That can be harder that you think.
I used a block of wood laid across the top and just tapped it with a hammer to set the unit in place.
Make sure that when you take it apart to save the bolt and the old cap unless you ordered a new cap.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

Removed 4 screwes on the top of the washer. Layed down the control panel and there was the inlets. Removed two screws and loosened the hose clamp. removed and installed new part.
It did the trick. No more problems.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

After pulling the knob out ( on position) a white retainer clip was visible behind the knob. Using a paper clip bent in to a "J" shape I was able to easily remove the retainer clip and knob . The old knob had several stripped teeth that caused the problem. The new knob came with the retainer clip installed . The knob slipped on and locked in position.