WBSR300FW General Electric Washer - Instructions

Just slipped it on. No problems, No Tools.

Remove control knob and replace it with new part.

One retaining clip to remove and replace part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. put the new part in and that was it.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

You tube is the only way to go!

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

I removed the front panel, disconect the Level Pressure Switch and conect the new one, the only thing that took me most of the tima was calibrate the instrument.
whene you disconct the hose that goes in th side of the L P S. to replace it for the new one you have to be care full. FIrst install the new part, then before you conect the hose let the machine fill up with water up to the firt level ( small load), to do this,calculate the water amount, then blow the hose to leave the hose free off air to create, a vacume then install it on the original position.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.