WPSF5170W0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Jonesboro, TN
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control set knob no longer turned the setting dial
I reviewed the service guide on Partselect and was able to take the old knob off the washer and say that the teeth on the knob had worn off, I called in and ordered the part on Saturday and the part was delivered in Wednesday, within 2 minuets from getting home from work the washer was fixed. My wife was ready to go out and buy a new washer when it only cost a little over $13.00 to get it fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Keizer, OR
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator spun but would not agitate
Replaced the plastic agitator coupler
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tammy from tracy, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the agitator was not sping
figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from INDIANAPOLIS, IN
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Agitator not agitating
Watch the videos you might be a little skeptical at first. I watched the videos about 8-10 times before I bought the part so I took my part out first then got back on you tube watched a few more videos and got on parts select website found the part matched it up to what I pulled out of my washer ordered it got to me in a weeks time put it in and working like new again cost about 14.00 shipping and part together saved about 200.00 per my estimate I had to fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Davie, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Debris in pump
Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ranburne, AL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator coupling in my washer was stripped out.
I had already removed the old coupling by removing pulling the agitator straight up off the coupling, then I removed the bolt that held the coupling in, and pulled the coupling up off the shaft.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beulah from MISSOURI CITY, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
CLOTHERS NOT AGITATING
REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from LONGVIEW, TX
- Parts Used:
- WH01X10310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
selector knob plastic teeth mostly gone, difficult to select wash cycle
Unplug washer to keep from running.Pull out on selector. After determining how knob was held in place, used coat hanger with short 90 on one end to catch clip holding knob in place. Pulled clip, removed knob.Placed clip on back of new knob just enough to hold. Placed knob on shaft, pressed down on clip to lock in place. All Done. Use of small flashlight is helpful. Replug washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from brooklyn, MI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Would not pump out water
Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SAINT CLAIR, MI
- Parts Used:
- WH23X10030
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining out of the washing machine
The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from TRAVERSE CITY, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer would fill, spin and drain, but was not agitating the clothes.
(As I am an older female, I used YouTube to review the repair before trying it. YouTube scared me, the actual repair was much easier) I removed the agitator from the washer which revealed the agitator assembly held in place by a bolt. After removing the bolt, the assembly was lifted off the spindle. I cleaned the grime off the agitator, the spindle and the bottom of the washer basket. New agitator assembly was placed onto the spindle and pushed down. There was a distinctive click when it slid into place. I replaced the bolt to the top of the assembly. tightened it down, then slid the agitator over the assembly, matching grooves to teeth until that also slid into place with a click. It honestly took me longer to clean the grime than to change the part. Agitator is working perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from WORCESTER, MA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator spins freely.
Pull off the agitator. Remove 1 bolt on coupler pull off coupler. Slide new coupler onto spindle. Replace bolt. Line up and slide on agitator. Seat it firmly in place. Done. Took all of 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from COCOA, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
the water, not get out (drain)
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from EAST PEORIA, IL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Very loose agitator so I thought
I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,
I also spent less than 12.00 to fix and a new one is over 600.00.
Thank You
Christine brooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Richland Hills, TX
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washing machine quit pumpig the water out.
Removed the old one and installed the new pump, by removing the front cover and disconnect everything.
Was this instruction helpful to you?
Thank you for voting!