WHDSR209GW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rob from Betterton, MD
- Parts Used:
- WH45X10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The machine would not spin and the agitator seemed to be siezed up. The inner tub had cracked and broken completely loose causing it to jam against itself preventing any movement.
1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michele from Deerfield Beach, FL
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer needed new knob and clip
simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Canastota, NY
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The knob on my washer would not turn so I could select load size
I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Ventura, CA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump was leaking due to a crack
We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Flagstaff, AZ
- Parts Used:
- WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic on the back of the knob that allows for engagement with the washing machine broke off. I replaced the knob and replaced the clip that hold it in place. Nothing to it. The part came within two days.
I just removed the clip and took off the old knob. I than put the new one on and replaced the clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Herrin, IL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Pump was making grinding noise
Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Truett from Kennesaw, GA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
hose had a small pin hole. leaked.
With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Clinton, NJ
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Pump was bad
I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Perrysville, IN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken straps
replaced them & working fine now....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Manti, UT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The pump was easy to put on the the washer still doesn't work . The water still just drains out.
First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry O. from Pie Town, NM
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
would not drain
Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luiz from Bethesda, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The washer was shaking a lot
I had to take out the front panel to access the Tub. Afterward the work wasn't hard.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Venice, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
Noisy Washing Machine, tub bangs around
The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from CLARKESVILLE, GA
- Parts Used:
- WH43X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Agitator free spins
This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from MARIETTA, SC
- Parts Used:
- WH43X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer wouldn’t agitate.
Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.
Was this instruction helpful to you?
Thank you for voting!