WJRR4170EC General Electric Washer - Instructions

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

Took complete tub assembly out of washer and inspected it. Did not find an obvious cause of leak but all 8 screws on inner tub hub were loose. As both tub nut and split ring were corroded, replaced them and the outer tub seal. Did a lot of cleaning!! As I was putting the trans assy back on the outer tub, I noticed a crack around the drain spout. At 1st, it looked like it belonged there but a closer look proved it didn't. I ordered a new outer tub (which came in 2 days) and I put the whole thing back together. Reassembly was far easier than disassembly was and I learned a whole lot about washers. YouTube is a great source of information.

I took off the broken knob since it was already loose. Then I removed the new part from its wrapper and lined the bolt up the knob. Inserting and pushing until it felt like the knob had a firm grip the job was done.

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

I had no difficulty dismantling the washer until I got to the hub nut. It was frozen to the cone shaped fitting it was resting in. I had to take a drill and a 3/16" drill bit and drill the flange of the hub nut and then take a chisel and break it off piece by piece. Once that was off, I lifted the tub out and tried to pry off the split ring under the tub and it too was corroded and broke when I tried to pull it off. So I would advise you to buy a hub nut and a split ring if you are replacing the tub bearing, just to be safe. I went to an appliance parts store here in town and bought them. When reassembling the tub, I couldn't get a wrench or pliers on the hub nut to get enough torque to tighten it securely. And since I didn't want to spend $43 to buy a spanner wrench for a one time repair, I went to Harbor Freight and bought a $15 dollar adjustable wrench and cut 3 1/2" off the handle so it would lay flat to the tub and used a hammer to tap on the handle to tighten it securely. If you do not find some way to tighten the tub securely, it will come loose in the spin cycle like it did on me twice before I purchased the adjustable wrench and modified it to work. Plus I still have a useable adjustable wrench. Additionally, I took the washer cabinet, the tub and the tub sleeve and power washed it to get years of grime off of it. The washer now operates like new, saving me hundreds of dollars.

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

Fold back control panel, pull water level knob off, and unlatch pressure switch. reverse procedure to install new switch.

unscrewed the old coupling, brushed off yucky build up and replaced, ta da back to washing clothes constantly !