WWSE5240GC General Electric Washer - Instructions

The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

Was easy. Removed pump, ordered yours and replaced

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

Repair went great. The large nut had to be soaked to free it but the part was an exact fit.

I watched the YouTube video. Great help. The part was at my house less than 24 hours after I ordered. Great delivery! The repair was a no brainer even for a novice like me.

This site and buying experience WOWED ME!!! After realizing what happened, I searched how to open up a washer, since I had never done it before. My search brought me to your site, which had an excellent 'how to' video for my exact problem of replacing the pump! I ordered the part, which was delivered to my door in LESS than 24 hours! Unfortunately, there was undrained water in the washing machine so while undoing the clamps on the old pump, the water drained on my kitchen floor, so beware of that issue. Because of the positioning of the pump, the clamps were a little tricky to redo, but completed without too much difficulty. I also had to 'unplug' (with a coat hanger snake)the drain tube connecting the pump to the back of the washing machine so it could flow to the outside drain pipe. This was the best internet buying experience I have ever had! Thank you so much! I fixed a 15 year old washing machine for about $40.00!!! (And I am a 57 year old grandmother ;-) Woohoo!!!

Unfortunately this did not solve my problem. After further inspection I still have the burning smell and the washer cuts off after it Agitates for a few seconds then in a minute or so it will Agitate a few more seconds and then cut off again. I also replaced the control panel still have the same problem. I would say it is the motor but the motor works fine in Spin Cycle. As for the Pump replacement it is very simple just follow the instruction Video on this site and 15 minutes later your new pump is installed. I will keep the pump since my new Washer uses the same part. P.S. The burning smell is not coming from the belt. It's almost like some kind of circuit protector is tripping and then a few minutes later it lets the washer start again.

Removed the front panel (retainer clips), removed two screws holding the top panel and door, removed all 4 dampening straps and replaced them with the new straps, put the components back in reverse order of removal.

Washing machine stopped draining, was looking into buying a new one. Thought maybe it was the pump, looked on-line and found one for around $50.00. Recieved the pump in pretty good time (3 days) The repair was not too bad, although the "ring clamp" was not very easy to work with. Hard to work it around the hoses in such a tight spot.

After noticing the leak, I moved the washer out to try to find the source. In the process, the Drain Hose Extension broke in two. As an emergency repair, I put the two halves together with duct tape. After running the washer again to try and find the leak, I discovered that it must have been the Drain Hose because now there was no leak. I then ordered a new one from PartSelect and replaced it with the repaired item.

Determined the drain hose on the back of the machine was leaking, due to my dog chewing on the hose. Replaced the hose with the new one, locked the dog out of the garage where the machine is located, problem solved.

I pulled the front panel off as described in the video on Partselect.coms video (very helpfull) and unpluged the pump, I was able to test the original pump and determine it to be good and ultimatly that was not the problem. However had it been it would have been a simple fix. returning the unused part was super simple and painfree!

One of the fastest repairs that I have performed. Took less than 15 minutes. Unhook wires, removed haoding screws, unclamped hoses. Reversed the process to install the new unit. Shipping was incredible. Ordered the part at 1400 on Thursday and had the part in hand Friday at 0900. One of the best on-line experiences that I have ever had. Thanks a bundle, Richard