WWA9850MAL General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gear oil leaking from transmission seal
i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- audrey from WHITING, NJ
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer shut off and would not go back on
After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BETHESDA, MD
- Parts Used:
- WH1X2026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Washer was not agitating or spinning
I followed the instructions on your website to diagnose the problem, select the part needed for the repair, and fix the problem. Everything was as described in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nydia from melbourne, FL
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
loud noise when spining
I did watch the video, that Parts Select included in an email. After that just follow the instructions in the video. You do need two people to do the job, since the belt needs to be tight. One for holding and one to tight the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Cedar Park, TX
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
It wouldn't spin!
Could smell burning rubber as it tried to spin, so figured it was the belt. No, I did no do it the hard way by removing the screws etc. I threaded the belt on the pulleys on one side, and slowly turned them, using my fingers to force thread the belt into place. Worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from CEDAR PARK, TX
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Cold water was not coming in very quickly in fact fill time went to about an hour
turn off water outlets, unplugged unit then removed water hoses, then removed the screws from the plate on the washer then removed the valve from the plate then unscrewed the clamp for the water inlet to the washer then removed the hose. then carefully removed the wire clips putting each one on the same connector on the new valve, then put everything back like I did when I took it apart and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from LOUISVILLE, KY
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The valve the controls hot water coming into the washer no longer passed hot water through.
I looked up the part on line, ordered it and installed. Veru easy since the part that needed repair was right out in the open.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Norfolk, VA
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washing machine tub would not fill up on rinse cycle.
Replaced the water control valve (the thing the washer hoses connect to on the back of the washer) There were 3 bolts that had to be removed and once the part was loose, there were four wires attached, I disconnect each wire from the old part and reconnected to the new part at the same time to keep from getting the wires mixed up. Then I bolted the new part back in place...worked perfect. Total cost of repair was less than 30 bucks...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CATHERINE from POCONO LAKE, PA
- Parts Used:
- WH1X2026
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
smelt rubber burning, diagnosed it as a belt
Turns out it wasn't the belt. The belt was fine, worked without water, replaced in washer spot, reconnected water, worked fine. Put clothes in, wouldn't agitate, smelt burning again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james r from cincinnati, OH
- Parts Used:
- WH1X2026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Wrench (Adjustable)
Oil-soaked drive belt split; wouldn't move agitator
Pulled washer away from wall. Observed problem. Ordered belt. Went on vacation. Cut belt in two to remove. Removed flex coupling to pump. Tried to force new belt onto big sheave, but couldn't really access properly. With help, tipped washer onto its front. Then access permitted forcing new belt onto big sheave by turning (only one direction permitted by gear box). Most of time spent cleaning up oil from gearbox which dripped on floor and splattered on back wall. Wonder how long 15 yr old gearbox will last?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Richmond, VA
- Parts Used:
- WH1X1951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
A load imbalance caused one of the four yokes to break in two.
I had to tilt the machine to gain access to the screw that holds the yoke bracket in place. Then I removed the one screw that holds the yoke bracket and removed the yoke and it's cushion. I then had to remove the two friction pads from the old yoke and install them on the new yoke. I was able to re-use the old yoke cushion and after re-assembling the yoke and cushion, I installed this assembly with the one screw. Righted the machine and the job was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Manchester, VT
- Parts Used:
- WH1X2757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer knob was broken
simply replaced the old knob with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwardo from Borrego Springs, CA
- Parts Used:
- WH23X42
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Water leaking out of the bottom of the washer
I own a vacation rental two hours from my home. Our guests
said that there was water coming out from under the washer.
I called our local handyman Lolo who is very bright. He came
over and looked at the washer and saw that a plastic part was leaking. He got on your website and put the part number in and we had our part within two or three days of ordering it.
I was impressed by your having this older part-maybe 15 year old washer,the fast delivery since we didn't do it by rush order. I also didn't have to hire an expensive repair service company. We are back in business thanks to your quick service and delivery. We will use you again in the future for sure.
Best Regards,
Trish W Haskell
Borrego Springs, CA
said that there was water coming out from under the washer.
I called our local handyman Lolo who is very bright. He came
over and looked at the washer and saw that a plastic part was leaking. He got on your website and put the part number in and we had our part within two or three days of ordering it.
I was impressed by your having this older part-maybe 15 year old washer,the fast delivery since we didn't do it by rush order. I also didn't have to hire an expensive repair service company. We are back in business thanks to your quick service and delivery. We will use you again in the future for sure.
Best Regards,
Trish W Haskell
Borrego Springs, CA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from millen, GA
- Parts Used:
- WH1X2757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
teeth worn off of knob
removed old knob pushed on new nrw one locked on wifh key
Was this instruction helpful to you?
Thank you for voting!
Water leaking out the bottom of washer during fill
Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.
Was this instruction helpful to you?
Thank you for voting!