WJRE5500GW General Electric Washer - Instructions

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

You tube is the only way to go!

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

Took off the front panel of the washer which exposed electrical wires going to top lid sensor. Took out old sensor installed new. Cut wires from old sensor and spliced wires from new sensor to machines wires that went to old sensor. Replaced front of washer. Washer works fine now.