FFT6001 Frigidaire Washer - Instructions

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

remove old belt, install new belt

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

watched the video, all instructions were perfect!

watched the video on website, printed instructions for feedback.

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.

The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightforward. And the washer no longer leaks!

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!