LTF2140ES0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Amarillo, TX
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer would function for 2 to 3 minutes and then pause. "PAU" appearing on the display.
Apparently the faulty switch was causing the washer to think that the door was open which would pause the wash cycle. The temporary fix was to disconnect/reconnect the door lock/switch assembly, thereby resetting the switch. Eventually though, the switch had to be replaced. The repair was simple. Unplug washer from power. Remove the metal band and spring from around the perimeter of the door seal. (I had to use needle-nose pliers for this step). Loosen the rubber seal near the door latch area only. Remove old latch by unscrewing the two screws, and disconnect all wired connections. Reconnect wired connectors using the new part and screw back on to the washer using the two screws. Reseat the rubber door seal and hold in place using the metal ring and spring you removed in the first step. Plug washer back in to power. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEITH from BEND, OR
- Parts Used:
- 137221600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Spin Cycle wouldn't work
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Merrimack, NH
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer door woild not lock and would not allow washer to operate
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Dover, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer would not spin out
First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.
THANKS
VERY happpy customer.
THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Burtonsville, MD
- Parts Used:
- 5304485917
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Kenmore 417.41042000 Front loading washer shakes
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Mastic Beach, NY
- Parts Used:
- 134371220
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Water leaking from inlet hose area.
Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
Part arrived 2 days later, took about 40 minutes to install.
Part arrived 2 days later, took about 40 minutes to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mandy from rock falls, IL
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer door handle broke
unscrewed the old handle, and screwed the new one on. It only took 2 minutes to fix. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from albertville, MN
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
tab broke off when the door was shut too hard.
2 screws and about 48 seconds of work. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- May from Abilene, KS
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door slammed shut
door not level son slammed shut and door strike broke
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Oswego, IL
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke off at the top
Like another commenter, my teenage daughter ripped the handle off at the top in a huff. My husband simply unscrewed the broken handle and replaced it with the new one. We now make sure to open the door from the middle of the handle, not the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from MAPLE SHADE, NJ
- Parts Used:
- 134743500
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No spin
No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Brazil, IN
- Parts Used:
- 134371220
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Wet clothes after spin cycle on front loader
Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Littleton, CO
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would not spin or complete spin cycle
E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door lock in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
First I removed the "wire" and spring that hold in the rubber seal at the door.
Then I removed the 2 screws that hold the door lock in place.
Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.
Runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Wolcott, VT
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle to the front load washer had broken off
Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from AURORA, CO
- Parts Used:
- 134370000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken front on dispenser drawer
Despite putting all the information about my washer in the order, I received a dispenser drawer that was similar to the one I needed, but would not fit. It was also a slightly different color than the original part on my machine, so obviously someone just threw it in a box and sent it to me. It wasn’t even wrapped in plastic! Just the part in a box, no instructions, no bill of sale, nothing. When I needed to return it because it wasn’t the proper part, I HAD TO PAY THE $10.00 TO SHIP IT BACK!!! Really poor customer service in my opinion. Hopefully I will at least get a credit for the incorrect part that I had to pay to return.
Was this instruction helpful to you?
Thank you for voting!