FAHE4045QW0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Amanda, OH
- Parts Used:
- 137221600
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Water would not drain or washer would not spin
Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherry from ellenburg depot, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard from upper sandusky, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer failed to drain
sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from burleson, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Unit did not drain
removed and replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from Ripley, WV
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer won't drain
My wife done the repair while I was out of town. She never tries to won't on anything in fear that she will mess it up.But she said she had it fixed in ten minutes. Just take the hoses off the pump, unplug, and unbolt where mounted. Then reverse to put on new one. Partselect is always very prompt to sent my parts and I have never had an issue with anything. I will buy all my parts from them from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from San Antonio, TX
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washer pump out
Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from Providence, NC
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer would drain most the time but not spin
This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from New York, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer Would not drain
Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.
Was this instruction helpful to you?
Thank you for voting!