FWY833KAS0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- CLARK from JUNEAU, AK
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken selector knob
removed broken knob..pushed new knob on..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from Mt. Vernon, OH
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Starter knob broke off the machine
I pulled off the broken knob's metal shaft that remained attached to the operating spindle and slid the knob onto the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diane from arlington hts., IL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob would not turn on tne dryer
i took the old knob off and put the new one on. it took about 10 seconds. it was simple.the service dept. was extremely helpful in getting the right knob. it was delivered the very next day. i would definitly recommend this company to anyone who has a parts problem.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randy from island park, NY
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Extremely easy. From finding the part on the website to installing on the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Spring, TX
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob that turns on the dryer had been broken for over 4 years.
It is so great to be able to turn my dryer on now without using my bare hand to turn the shaft that the knob was to go on. Nothing needed other than pushing knob in place. I so wish I had thought of looking online for a replacement part 4 years ago. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Terre Haute, IN
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob broke
I ordered replacement knob for washing machine. It arrived by fedex in 3 days. Ordering was easy and transaction went as smooth as it could. I will order again if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Cambridge, MA
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
Just put the new one on! Absolutely great service!!!!
A+++++++++++++++++++++++++++++++++++++
A+++++++++++++++++++++++++++++++++++++
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Calexico, CA
- Parts Used:
- 134418700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from wilmington, IL
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would flood out the floor now and then
One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Magnolia, MS
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Excess noise in pump, forigien drill bit hitting inpeller blades
Very simple, unplug washer for safety, remove 2 Phillips screws form bottom of front panel, slide panel down to slip the ears out of their slots. set panel off to side, remove the electrical plug on the pump, unscrew the two hold down Phillips screws, raise the pump up and slid a heavy absorbent towel under the pump, loosen the two clamps, slide the hoses off, remove the sloppy wet towel, install the new pump, and screw it down, push the electrical connection on, slip the hoses on , clamp them in place, install the front cover by aligning the slot and ears up, use a screw driver or something the raise the panel up in place then install the last 2 screws plug it in your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Portsmouth, VA
- Parts Used:
- 3204401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Agitator
Unplug unit. Unscrew securing nut, remove agitator, install new part (ensuring splines mate properly) and secure with nut. The nut is molded into the plastic top of the agitator, therefore no tools were required. Very simple and straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Daingerfield, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hose leaking
lifed the lid .remove oud hose and replaced with new hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Landing, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old belt
Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.
Was this instruction helpful to you?
Thank you for voting!