MWX223REW1 Frigidaire Washer - Instructions

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so far!

Unhooked old hose and replaced with new one.

I met her in the basement lonely and needing a fix i went down on my knees and started to take off her worn out belt slowly down past her pulley and off her soon to be hot transmision. i gently held her pulleys as i wrapped her new belt around them. putting her chasies back together and plugging her in i pushed her button and off she went shakening and rallting once again.

Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

Straight-forward: remove hose wire-clamps, unplug electric/ground, unbolt bottom pump bracket (two studs), reset new pump outlet to match factory configuration (easy, but watch to not roll/pinch o-ring seal), reinstall in reverse order (wire-clamps are toughest part - clamping tools, as noted, are helpful). Also, clean hoses, esp. if old, and it helps to use some kind of vinyl guard (like Amorall) on them for lube and preservation. Leak-test. Plan for some water leakage during removal - sopping/vac'ing out the drum, catching hose drainage in a shallow pan or with a towel will help.

It was easy. No problem getting the to v-belt.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!