F21C645CT0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Calexico, CA
- Parts Used:
- 134418700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Eugene, OR
- Parts Used:
- 134190200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer leaked at water inlet valve
The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightforward. And the washer no longer leaks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Portland, OR
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water overflowed not shutting off.
I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hamilton, OH
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My washer started making a loud, screeching noise and then stopped working.
Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad drive belt
remove old belt, install new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Daingerfield, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hose leaking
lifed the lid .remove oud hose and replaced with new hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Humberto Aarón from Castroville, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The washer hose assembly had mutiple tears in the bellow section of the hose, towards the outlet net the spout.
Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).
Was this instruction helpful to you?
Thank you for voting!
Out of country repair needed
This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!