FAFW3001LW3 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Annie from Santa Clara, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer drum would not spin
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Saint Augustine, FL
- Parts Used:
- 134366400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manny from Old Bridge, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine wouldn't go into final spin.
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MADISON, IN
- Parts Used:
- 134370000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
i broke the soap dispenser on my washer
love parts select have used them several times for parts great company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer drained withn no spin
Remove top of washer, remove door lock assembly,install new assembly replace top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy L from Twin Lake, MI
- Parts Used:
- 134371220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the part cracked from water freezing
First I removed the two screws that hold the part in place. I then pulled the part out about 3 inches and disconnected the three wires from the part and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEDFORD, OR
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Leaking drain pump
Replaced drain pump using this walk through. Different models, but pretty straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica Ramaker from SAINT PAUL, MN
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Strike
Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from GUILFORD, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Doesn’t close
Remove screws take off striker .Put striker back on with screws back on
Tighten screws. Took 5 minutes
Tighten screws. Took 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from OROFINO, ID
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not drain or spin
Removed the 4 screws holding the top on. Pulled top forward to release front catches and stood top up out of way. Removed 2 screws holding door lock. Could not unplug wire plugs from door lock because wires too tight. Removed 2 screws holding lower front panel and removed panel. Pulled door lock down and unplugged old lock and plugged in new lock. It was easier to position door lock to reinstall screws by working from top, so top removal wasn't a total waste of time. Reinstalled front panel and top. Machine works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buford from LAWTON, OK
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump froze during subzero temp
Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Eugene, OR
- Parts Used:
- 134371220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer was in the garage, and we had a hard freeze. Water in the valve froze, breaking the valve.
Took the top off the washer, removed the valve, installed the new one, back in buisness. It was so easy to order the part, and have the repair done in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Wichita, KS
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch on door broke. It is made of plastic and just broke off.
just unscrewed the old one and put a new one on.
I bought two just in case this one breaks too.
I bought two just in case this one breaks too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyran from Montclair, NJ
- Parts Used:
- 134762000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer gave error code 31
I opening that top from the rear and saw the same part order plugged in then new part attached it properly and then was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Jacksonville, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL
Phil
Jax, FL
Was this instruction helpful to you?
Thank you for voting!