FAFW3001LW2 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Philip from Jacksonville, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL
Phil
Jax, FL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyran from Montclair, NJ
- Parts Used:
- 134762000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer gave error code 31
I opening that top from the rear and saw the same part order plugged in then new part attached it properly and then was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Brandon, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Washer would spin in any cycle
Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Middleboro, MA
- Parts Used:
- 134371220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The valve had cracked so water was leaking out from the cracked area.
After getting a quote for $140 for a repair, I decided to try ordering online and hope for the best. I am delighted to say it was incredibly easy! All I had to do was remove the broken valve by unscrewing the water hoses with a wrench and remove two screws that held the valve on with a screw driver. Next, I popped in the new piece, replaced the screws with the screwdriver and attached the hoses, then tightened them with the wrench. Very easy! 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery David from Chesaning, MI
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bkn door strike
Very simple hardly worth writing about.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cos Cob, CT
- Parts Used:
- 131763302
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door on washer broke lots of laundry to do!
I was amazed at how quickly my part came for the washer and it came to me on a Saturday
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Winchester, IN
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Strike
Nothing to it rteall. The great thing was how fast this company got the part to me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard A. from Newnan, GA
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Hungry dog ate the door latch on my front-load washer
ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Colorado Springs, CO
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door striker was broke
unscrewed the 2screws from the striker on the washer door first. Then put screwed new striker on door with its new screws. It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from edinboro, PA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
machine would not go into final spin, clothes saturated
with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Haymarket, VA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Washer would agitate but not enter spin cycle
Washer error code said control board($200.) but this web site said Door Lock and Switch assembly($80). Web site was correct, thankyou for saving me money and time for the real repair needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from San Diego, CA
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Machine would not start
Unscrew the the bad part, screw on the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from League city, TX
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Machine wouldn't spin
Removed 2 screws , unplugged the old switch , replaced with new one and secured with screws . Easy !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kamlyn from Huntington Becah, CA
- Parts Used:
- 131763302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch to door broke and would not stay shut
I unscrewed the two screws and replaced with new door striker and used the same two screws I took out. It took me seriously less than 2 minutes and I am a woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michelle from swanzey, NH
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer wouldn't spin shut off with 6 mintes to go
I found this wonderful web site, after removing the cover and running a diagnostic to find it was either the door lock or the TCP control board. Control board unable to find any information on was scared to call the repair man as they usually cost about $500.00. I am a single mother and order the door lock and just like that I was able to repair it myself. Thanks you so much!!!
Was this instruction helpful to you?
Thank you for voting!