FAFW3001LW2 Frigidaire Washer - Instructions

Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids

Followed the youtube video step by step. Very helpful video. Be careful of hinge screws. They are very easy to strip. Had to buy a special tool to remove stripped screws. Advice go ahead and purchase the 4 screws. 3 for the hinge and 1 for spare. Rest of the repair was easy. Less than an hour to complete.

screwed in the new legs and leveled it off again.

Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.

First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!

Despite putting all the information about my washer in the order, I received a dispenser drawer that was similar to the one I needed, but would not fit. It was also a slightly different color than the original part on my machine, so obviously someone just threw it in a box and sent it to me. It wasn’t even wrapped in plastic! Just the part in a box, no instructions, no bill of sale, nothing. When I needed to return it because it wasn’t the proper part, I HAD TO PAY THE $10.00 TO SHIP IT BACK!!! Really poor customer service in my opinion. Hopefully I will at least get a credit for the incorrect part that I had to pay to return.

First, I recommend you have a second pair of hands. The chrome door is quite heavy. Using Phillips screwdriver I removed the screws that attached the door to the frame. I had a helper hold the door while I removed the screws.
Once hinge screws were removed I put a towel down on a counter to keep the front of the door from getting marked up and proceeded to remove all of the screws around the back of the door so that I could lift the frame up enough to remove the broken hinge and insert the new hinge. It was a bit tricky to get the new hinge with bushings in place. I gently lifted the frame up with a flat head screw driver to widen the opening so I could get the bushings on the new hinge into position on the frame. Make sure they are properly inserted before you start tightening up screws.
Next, replaced all the screws on the frame, returned to the washing machine with helper who held the door up while I aligned the holes in the new hinge to the holes in the frame around the opening to the washer.
After everything was secured and tightened, to my surprise, the door latch did NOT line up with catch without lifting up about a 1/4" or a little more, on the bottom of the door. If someone slams the door without doing that you could break off part of the plastic latch or damage the catch inside the door frame.
I believe the original holes on the door frame were not drilled precisely during the manufacturing process and that is why the bottom bushing broke. We have always had to lift up a bit on the door to line up the latch with the catch. Eventually the strain on the bottom bushing caused it to break and then the door tilted down so you had to lift it up about 3/4 inch to latch it. I bought new hinge because if the top bushing broke the door could have come off.
Next time I buy a washing machine, I will pay more attention to the line up of the door latch with the door catch.
Flashlight helped me line up the holes.

The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!

Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.

I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went.
Garry

first removed top of machine. removed 3 valve core wires set. Then removed left top screw on valve. Then removed vent tube to get to lower right screw. disconnected hose connect rack so valve housing could be removed & new installed. Rapped insulation around valve & installed. Put everything back together in reverse order.

I watched the u-tube video and followed what he did and it was fixed. Reason it took over 15 min I had to find the correct bit for the screw. I think your web site is great thanks

2 screws off and put new striker in and replaced the screws

(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .

My 10 yr old son removed the two screws, placed the new strike on, and screwed it back into place!! So easy a child did it!!