FAFW3001LW4 Frigidaire Washer - Instructions

easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL

Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!

After getting a quote for $140 for a repair, I decided to try ordering online and hope for the best. I am delighted to say it was incredibly easy! All I had to do was remove the broken valve by unscrewing the water hoses with a wrench and remove two screws that held the valve on with a screw driver. Next, I popped in the new piece, replaced the screws with the screwdriver and attached the hoses, then tightened them with the wrench. Very easy! 10 minutes total.

Very simple hardly worth writing about.

I was amazed at how quickly my part came for the washer and it came to me on a Saturday

Washer error code said control board($200.) but this web site said Door Lock and Switch assembly($80). Web site was correct, thankyou for saving me money and time for the real repair needed.

unscrewed the 2screws from the striker on the washer door first. Then put screwed new striker on door with its new screws. It was a piece of cake.

Nothing to it rteall. The great thing was how fast this company got the part to me!

ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!

Unscrew the the bad part, screw on the new part

with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.

removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys

with a code it gave me i was able to determeine it was the door lock switch it was so easy it was unbelievable

Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.

I took off the face and top of washer changed the drain hose.and put it back together and it started leaking .word to the wise. mmake sure the back side of the drain hose that is not visable is all the way on then tighten.