FAFS4174NW0 Frigidaire Washer - Instructions

Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!

Very simple hardly worth writing about.

I was amazed at how quickly my part came for the washer and it came to me on a Saturday

Nothing to it rteall. The great thing was how fast this company got the part to me!

unscrewed the 2screws from the striker on the washer door first. Then put screwed new striker on door with its new screws. It was a piece of cake.

Washer error code said control board($200.) but this web site said Door Lock and Switch assembly($80). Web site was correct, thankyou for saving me money and time for the real repair needed.

with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.

put new part did reset on main controles

Unscrew the the bad part, screw on the new part

ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!

as on the video. so easy. took longer to clean-up

In order to get to the switch located on the right front behind the from panel the top had to be removed with 2 screws holding it in place on the back of the machine. Next the top front control panel needed to be removed by first removing the detergent drawer on the top left of the washer. There are 3 screws that need to be removed behind the slide out dispenser. ALS there are 2screws on the top left and right that need to be removed.. Once these are all removed you can slip the control panel up and over the top and let it rest there. I might suggest that you should unplug the machine from the electrical outlet. Once this is all done there are 4 screws holding the bottom of the front panel that must be removed. If you have pedestals on your machine you can pull the drawer out to get to them. If not you will need tp tilt the machine back and using a block let it rest on it to get to them. Once these are removed you will need to remove the block and set the washer back on its feet. There are now 2 screws at the top to be removed. Once removed lift and pull out the front panel. Set aside. You are now ready to remove the front rubber boot from the washer.. There is a spring that is behind the front rubber that needs to be removed. Using a screwdriver, at the bottom of the front boot you will see the springs once you peel a bit of the rubber back. Remove the spring and set aside.. Now you are ready to remove the door lock switch. Using a Phillips screwdriver remove the screws from the front panel and push the switch back toward the rear. It should pop out very easy. Unplug the switch from the harness and replace with a new switch.. Put the machine back together in the reverse order. Hope this helps.

I replaced doorlok as every one sujested but that did not fix it I then replaced thr control panel with a new upgraded one. It is not that simple for an amature. New control came with one of the control shafts missing had difficulty getting it in position so so control would be on right function. after all that I found diagnostic instructions taped to bottom of washer

During this repair job, I replaced the outer door cover and door hinge of this front loading washer. The outer door cover had cracked and shattered above the top hinge pin, leaving only the lower hinge pin to keep the door mounted onto the washer. The outer door cover contains the door hinge housing. Initially, I could not remove the hinge from the front of the washer, because the attaching flat-head screws were REALLY torqued onto the washer. My hand held screwdriver was unable to loosen these screws, so I bought a Black & Decker cordless 12V impact driver from Home Depot for $59. This power tool worked great, and I removed the hinge assembly and door from the washer. When you're using the impact driver, make sure you've got the correct sized bit for the Phillips head. You can buy a bit set at Home Depot. If you don't use the correct size, you'll just strip the head, and then you'll also have to buy a damaged screw extractor. Once the hinge was removed, I discovered that the lower hinge arm had been bent, due to the door hanging off just the lower arm. When I attempted to straighten out the hinge arm, it broke off. After a few choice words, I ordered a new hinge assembly from PartSelect. Once I received the new hinge, I reassembled the door, and attached the hinge to the washer. When seating the plastic hinge bushings into the outer door hinge housing, make sure the slotted tabs of both hinge bushings are fitted snugly into the hinge housing. You won’t be able to reassemble the inner and outer door covers if the bushings are not seated properly, I finally got everything back together, and now my washer works great. Using perfect hindsight, I would also recommend that my fellow handymen replace the proprietary flat-head screws which hold the hinge onto the washer. My first attempts to remove the hinge screws damaged them pretty badly. You should also consider replacing all the screws which hold the inner and outer door panels together.

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.