FWT445GES2 Frigidaire Washer - Instructions

Watched the video on website and followed what they said. Worked great.

Pump replacement quite simple - most difficult part of job was figuring out how to disassemble outer washing machine panels. Pump required disconnecting 2 hoses and an electrical connection.

the work is simple, its getting it done. The pins that hold the shocks in are very hard to get to and no room to swing a hammer. I had to use a C- clamp on the left upper in and it was no picnic. The washer in the video was a little different than mine.

pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...

First I tried to unscrew the two screws holding the latch with a phillips screwdriver. When it wanted to slip, I took a closer look at the screw heads and saw they were square drive. I got the proper tool and removed the screws, replaced the latch and replaced the screws in a few minutes.

I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!

(This is reply #2 of 2)
After I finally got all of the parts (at least the rear brackets and screws) I found that the panel only had one of two holes for the two horizontal screws.
After drilling a new hole in the left rear bracket position, I discovered that the 2 screws could not be threaded into the bracket pilot holes. Theyt froze up at the top of the taper in the threads. I had to increase the size of the hole 1/64" to get the screws in. There also is a trick to getting the bracket through the punched out hole in the panel- you must angle the bracket corner to corner then apply about 10# of preasure to the bracket to force it through the hole.
Other than that, the panel install went pretty well. Now I have to get the front brackets and springs and screws which are on backorder...

The replacement of the Shock Absorber Kit was hampered on the right side by a metal box that was mounted just a little shorter than the bottom plastic pin. the deadblow hammer with the dowel worked with all the pins including the impeded pin and the top right pin which had to be removed at an angle. The replacement did not repair the washer - it is the tub bearing which went in a previous washer of a similar model about 4 years ago.

Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!

Removed the back and lower panel in the front of machine. Turned it on its side to replace spring, not tools required. Then stood it up and replaced both shocks by removing plastic pins that hold them in place, no tools required. The only time you need tools is to remove the metal panels to get to the parts. Now it makes no noise and runs like a new washer. Paid $140 for the parts, a new machine would have cost over a thousand and would be one of those digital nightmares that don't last as long. This machine is 18 years old.

I watched the videos and replaced the shocks and suspension springs. This worked to stop the unit bouncing completely and cut the banging noise in half. Further diagnosis revealed a damaged drum and outer shell. The repair itself was very simple and didn't require special tools or skills. There is a tricky shock absorber locking pin on the right shock bottom position. There is a control box of some sort that prevents the complete removal of the pin without breaking it. On install, I simply pushed the pin through from the front. Ultimately, I ended up replacing the unit. However, I found the site to be extremely helpful. Great service.

It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad.
I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!

Replaced both the water inlet valve and the tank pressure switch to eliminate any possible cause. The repair was easy, and now the washer works fine.