LA600AXD1 Frigidaire Washer - Instructions

watched the video, all instructions were perfect!

The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

remove old belt, install new belt

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!

The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightforward. And the washer no longer leaks!

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.

lifed the lid .remove oud hose and replaced with new hose

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

removed front cover pushed in tensioner by hand walked belt off pulleys tilted belt removed lock ring pulled tensioner off noticed right rear lower tub brace broke at spot weods drilled out spot welds nut and bolted rear brace put springs back on base and installed belt works like new and saved myself from replacing lower washer tub frame so 70.00 and she up and running again

The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.

remove everything per your installation sheets which were right on ,everything when great. thank you .The only thing i had a problem with was ordering your bolts. The order list was not clear on how many bolts you get when you order. It did not say per screw I order 1, thinking it was the set of 5 but it was 1. ps460201 also bolts #ps3655064 i order 1 but there two Please let everyone know that .Again thank you great instruction Gary

Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.